Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1998 Toyota Supra car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1998 Toyota Supra automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1998 Toyota Supra
- 1998 Toyota Supra 3.0 L6 GAS, CC:2997, Fuel Injection, Engine VIN:, Desg:D
- 1998 Toyota Supra Twin Turbo 3.0 L6 GAS, CC:2997, Fuel Injection, Engine VIN:, Desg:E
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Toyota Supra AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Toyota Supra cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 1998 Toyota Supra 3.0 L6 GAS
Front
- Raise and support vehicle, then remove front wheels.
- Disconnect exhaust pipe, support rings, and support O-rings.
- Remove cotter pin, and lock cap and depress brake pedal and remove wheel hub nut.
- Remove brake caliper and support with wire. Remove rotor.
- Remove ABS speed sensor from steering knuckle, then loosen nuts on lower side of shock absorber. Do not remove bolts at this time.
- Remove lower suspension arm brace bolts.
- Place reference mark on driveshaft and side gear shaft.
- Remove six hexagon bolts and three washers while depressing brake pedal. Apply a light coat of eng...
CLICK HERE TO GET FULL ACCESS TO 1998 Toyota Supra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Toyota Supra AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Toyota Supra cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 1998 Toyota Supra Twin Turbo 3.0 L6 GAS
Front
- Raise and support vehicle, then remove front wheels.
- Disconnect exhaust pipe, support rings, and support O-rings.
- Remove cotter pin, and lock cap and depress brake pedal and remove wheel hub nut.
- Remove brake caliper and support with wire. Remove rotor.
- Remove ABS speed sensor from steering knuckle, then loosen nuts on lower side of shock absorber. Do not remove bolts at this time.
- Remove lower suspension arm brace bolts.
- Place reference mark on driveshaft and side gear shaft.
- Remove six hexagon bolts and three washers while depressing brake pedal. Apply a light coat of eng...
CLICK HERE TO GET FULL ACCESS TO 1998 Toyota Supra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Toyota Supra AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Toyota Supra cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 1998 Toyota Supra 3.0 L6 GAS
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove bolts securing oxygen sensor and heat insulator.
- Remove exhaust pipe bolts and nuts from support bracket.
- Remove two exhaust pipe support rings, O-rings, gasket and then remove exhaust pipe.
- Remove heat insulator nuts.
- Remove center floor crossmember brace bolts.
- Remove two center support bearing bolts. While removing set bolts, support center support bearing by hand so that the transmission and intermediate shaft and propeller shaft remain straigh...
CLICK HERE TO GET FULL ACCESS TO 1998 Toyota Supra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Toyota Supra AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Toyota Supra cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 1998 Toyota Supra Twin Turbo 3.0 L6 GAS
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove bolts securing oxygen sensor and heat insulator.
- Remove exhaust pipe bolts and nuts from support bracket.
- Remove two exhaust pipe support rings, O-rings, gasket and then remove exhaust pipe.
- Remove heat insulator nuts.
- Remove center floor crossmember brace bolts.
- Remove two center support bearing bolts. While removing set bolts, support center support bearing by hand so that the transmission and intermediate shaft and propeller shaft remain straigh...
CLICK HERE TO GET FULL ACCESS TO 1998 Toyota Supra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1998 Toyota Supra vehicle.
|
| Access the Complete guide! |
