1999 Acura CL Brake Service (ONLINE REPAIR MANUALS)

Auto Parts Search


Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!
Help me findSearch
Get Full Access Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1999 Acura CL car and truck repair procedures including Acura engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up & drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix your 1999 Acura CL automobile. Try the Automotix DIY solution today!
DIY REPAIR SAMPLES > CONTINUE EXPLORING >

We have info for following modifications of 1999 Acura CL

  • 1999 Acura CL 3.0 V6 GAS, CC:2997, Fuel Injection
  • 1999 Acura CL 2.3 L4 GAS, CC:2254, Fuel Injection

BRAKE SERVICE PROCEDURES FOR 1999 Acura CL AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura CL cars and light trucks from 1990+.

Anti-lock Brakes -> Troubleshooting -> ALB Checker -> CL -> CL & RL -> Fail-Safe Motor Relay -> Function Test -> Integra -> Integra & TL -> RL -> Solenoid Leak Test -> Temporary Driving Conditions -> TL -> Warning Lamp -> Warning Lamp Circuit -> Wheel Sensor Signal Confirmation
Vehicle: 1999 Acura CL 3.0 V6 GAS

ALB Checker

Never drive vehicle while ALB checker is operating. A collision may result from a reduction or complete loss of braking ability.

The checker should be used to confirm proper system operation under any of the following conditions:

  • After replacing or bleeding system fluid.
  • After replacing any ABS component.
  • After any body or suspension repair that may cause malfunctions within wires or sensors.
Function Test
  • Park vehicle on level ground with wheels blocked and parking brake set. On models equipped with manual transaxle, place in neutral. On models equipped with automatic tran...

CLICK HERE TO GET FULL ACCESS TO 1999 Acura CL BRAKE SERVICE PROCEDURES

BRAKE SERVICE PROCEDURES FOR 1999 Acura CL AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura CL cars and light trucks from 1990+.

Power Brake Units -> Adjustments -> Pushrod Clearance
Vehicle: 1999 Acura CL 2.3 L4 GAS

Pushrod Clearance

Refer to "Hydrau... "

CLICK HERE TO GET FULL ACCESS TO 1999 Acura CL BRAKE SERVICE PROCEDURES

BRAKE SERVICE PROCEDURES FOR 1999 Acura CL AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura CL cars and light trucks from 1990+.

Disc Brakes -> Caliper Service -> Assemble & Installation -> Front -> Integra, RSX, 2.2CL, 2.3CL, 2.5TL, 3.0CL & 1997-98 3.2TL -> MDX, 3.2CL, 3.5RL & 1999-2002 3.2TL -> Rear -> Removal & Disassemble
Vehicle: 1999 Acura CL 3.0 V6 GAS

Front

Removal & Disassemble
  • Raise and support front of vehicle, then remove tire and wheel assemblies.
  • Remove banjo bolt and disconnect brake line. Secure hose in raised position.
  • Remove pin bolt and caliper, Figs. through .
  • Remove pad spring.
  • Position suitable block of wood or shop rag in caliper opposite piston.
  • Remove piston by applying compressed air into fluid inlet port.
  • Remove piston boot and seal.
Assemble & Installation
  • Clean caliper bore and piston with brake fluid, then inspect for excessive wear or damage.
  • Apply suitable grease and install new piston seal in cylinder groove.
  • In...

CLICK HERE TO GET FULL ACCESS TO 1999 Acura CL BRAKE SERVICE PROCEDURES

BRAKE SERVICE PROCEDURES FOR 1999 Acura CL AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura CL cars and light trucks from 1990+.

Power Brake Units -> Precautions -> Radio Coded Theft Protection System
Vehicle: 1999 Acura CL 2.3 L4 GAS

Radio Coded Theft Protection System

Anti-theft radios have a coded theft protection circuit. The security code number must be obtained before disconnecting battery, removing radio fuse or ...

CLICK HERE TO GET FULL ACCESS TO 1999 Acura CL BRAKE SERVICE PROCEDURES

BRAKE SERVICE PROCEDURES FOR 1999 Acura CL AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura CL cars and light trucks from 1990+.

Hydraulic Brake Systems -> Component Replacement -> Master Cylinder
Vehicle: 1999 Acura CL 3.0 V6 GAS

Master Cylinder

  • Disconnect primary and secondary brake lines from master cylinder.
  • On models equipped with fluid level sensor, disc...

CLICK HERE TO GET FULL ACCESS TO 1999 Acura CL BRAKE SERVICE PROCEDURES

BRAKE SERVICE PROCEDURES FOR 1999 Acura CL AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura CL cars and light trucks from 1990+.

Disc Brakes -> Caliper Service -> Assemble & Installation -> Front -> Integra, RSX, 2.2CL, 2.3CL, 2.5TL, 3.0CL & 1997-98 3.2TL -> MDX, 3.2CL, 3.5RL & 1999-2002 3.2TL -> Rear -> Removal & Disassemble
Vehicle: 1999 Acura CL 2.3 L4 GAS

Front

Removal & Disassemble
  • Raise and support front of vehicle, then remove tire and wheel assemblies.
  • Remove banjo bolt and disconnect brake line. Secure hose in raised position.
  • Remove pin bolt and caliper, Figs. through .
  • Remove pad spring.
  • Position suitable block of wood or shop rag in caliper opposite piston.
  • Remove piston by applying compressed air into fluid inlet port.
  • Remove piston boot and seal.
Assemble & Installation
  • Clean caliper bore and piston with brake fluid, then inspect for excessive wear or damage.
  • Apply suitable grease and install new piston seal in cylinder groove.
  • In...

CLICK HERE TO GET FULL ACCESS TO 1999 Acura CL BRAKE SERVICE PROCEDURES

Shop online for auto body parts, engines, wheels, lights...

More parts
Help me findSearch
Auto Repair Quick Search
Help me find
Search DIY repair manuals by VIN...
Vehicle Identification Number is a unique serial number used by the automotive industry to identify individual motor vehicles

Find out what info we have for your vehicle

Need To Fix Your Car or Truck?
Save Money With Free Car Insurance Quote
FREE car insurance quote
Enter Zip Code:
Auto Repair Quick Search
Help me find