Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1999 Acura Integra car and truck
repair procedures including Acura engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1999 Acura Integra automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1999 Acura Integra
- 1999 Acura Integra GS 1.8 L4 GAS, CC:1834, Fuel Injection
- 1999 Acura Integra GSR 1.8 L4 GAS, CC:1797, Fuel Injection
- 1999 Acura Integra LS 1.8 L4 GAS, CC:1834, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 1999 Acura Integra AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura Integra cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Assemble & Installation -> Front -> Integra, RSX, 2.2CL, 2.3CL, 2.5TL, 3.0CL & 1997-98 3.2TL -> MDX, 3.2CL, 3.5RL & 1999-2002 3.2TL -> Rear -> Removal & Disassemble
Vehicle: 1999 Acura Integra GSR 1.8 L4 GAS
Front
Removal & Disassemble
- Raise and support front of vehicle, then remove tire and wheel assemblies.
- Remove banjo bolt and disconnect brake line. Secure hose in raised position.
- Remove pin bolt and caliper, Figs. through .
- Remove pad spring.
- Position suitable block of wood or shop rag in caliper opposite piston.
- Remove piston by applying compressed air into fluid inlet port.
- Remove piston boot and seal.
Assemble & Installation
- Clean caliper bore and piston with brake fluid, then inspect for excessive wear or damage.
- Apply suitable grease and install new piston seal in cylinder groove.
- In...
CLICK HERE TO GET FULL ACCESS TO 1999 Acura Integra BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Acura Integra AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura Integra cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Master Cylinder
Vehicle: 1999 Acura Integra LS 1.8 L4 GAS
Master Cylinder
- Disconnect primary and secondary brake lines from master cylinder.
- On models equipped with fluid level sensor, disc...
CLICK HERE TO GET FULL ACCESS TO 1999 Acura Integra BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Acura Integra AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura Integra cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> Front -> Rear
Vehicle: 1999 Acura Integra GSR 1.8 L4 GAS
Front
- Raise and support front of vehicle, then remove tire and wheel assemblies.
- Remove pin bolt and pivot caliper up away from rotor.
- Remove brake pad shims and pads, Figs. through .
- Clean caliper and inspect for excessive wear or damage.
- Install pad retainers, shims and pads.
- Back out bleed screw and push in piston to allow caliper to fit over pads. Tighten bleed screw
- Pivot caliper into position, install pin bolt and tighten.
Rear
- Raise and support rear of vehicle, then remove tire and wheel assemblies.
- Remove caliper shield and release parking...
CLICK HERE TO GET FULL ACCESS TO 1999 Acura Integra BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Acura Integra AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura Integra cars and light trucks from 1990+.
Power Brake Units -> Diagnosis & Testing -> Check Valve Test -> Function Test -> Leak Test
Vehicle: 1999 Acura Integra LS 1.8 L4 GAS
Function Test
- With engine stopped, depress brake pedal several times.
- Depress pedal hard and hold for 15 seconds. If pedal sinks, master cylinder, brake line or brake caliper is faulty.
- With brake pedal depressed, start engine. If pedal sinks slightly, vacuum booster is operating. If pedal height does not vary, booster or check valve is faulty.
Leak Test
- With engine running, depress brake pedal and hold, then stop engine. If pedal height does not vary with brake pedal depr...
CLICK HERE TO GET FULL ACCESS TO 1999 Acura Integra BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Acura Integra AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura Integra cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service
Vehicle: 1999 Acura Integra LS 1.8 L4 GAS
Do not disassemble brake boost...
CLICK HERE TO GET FULL ACCESS TO 1999 Acura Integra BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Acura Integra AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Acura Integra cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service
Vehicle: 1999 Acura Integra GS 1.8 L4 GAS
Components are not designed to be rebuilt. If...
CLICK HERE TO GET FULL ACCESS TO 1999 Acura Integra BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1999 Acura Integra vehicle.
|
| Access the Complete guide! |
