Auto Parts Search

BRAKE SERVICE PROCEDURES FOR 1999 BMW 323IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 BMW 323IS cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> Front -> Pads, Replace -> Rear
Vehicle: 1999 BMW 323IS 2.5 L6 GAS
Pads, Replace
Front
- Raise and support vehicle, then remove front tire and wheel assemblies.
- Remove retaining spring, as required.
- Disconnect brake pad wear indicator connector from lefthand side of caliper.
- Remove plastic plugs and remove brake hose out from bracket.
- Remove guide bolts and lift brake caliper toward vehicle rear.
- Remove brake pads and suspend caliper aside with suitable wire.
- Reverse procedure to install, noting the following:
- Turn caliper piston back into bore using fixture tool No. 34 1 050, or equivalent.
- Check fluid level and bleed brake system as required.
- Replace du...
CLICK HERE TO GET FULL ACCESS TO 1999 BMW 323IS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 BMW 323IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 BMW 323IS cars and light trucks from 1990+.
Power Brake Units -> Diagnosis & Testing -> Brake Booster Low-Pressure Test
Vehicle: 1999 BMW 323IS 2.5 L6 GAS
Brake Booster Low-Pressure Test
- Disconnect brake booster vacuum hose.
- Install vacuum test tool No. 34 3 100, or equivalent, between booster and check valve.
- Start engine and build up partial vacuum.
- Switch engine off.
- Press brake pedal to set partial vacuum of no more than 12 psi.
- When brake pedal is not pressed, partial vacuum ...
CLICK HERE TO GET FULL ACCESS TO 1999 BMW 323IS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 BMW 323IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 BMW 323IS cars and light trucks from 1990+.
Disc Brakes -> Adjustments -> Parking Brake
Vehicle: 1999 BMW 323IS 2.5 L6 GAS
Parking Brake
- Ensure parking brake lever is fully released and cables operate freely, then raise and support vehicle.
- Remove one wheel bolt from each wheel.
- Rotate wheel until bolt hole is aligned with adjustment screw.
- Turn adjusting screw until wheel can no longer turn.
- On 1998-99 M3, 740 and 750 models, loosen adjusting screw eight notches.
- On 323Ci, 325, 328Ci and 330 and 2000 323i and 328i and 1999 323i and 328i Sedan m...
CLICK HERE TO GET FULL ACCESS TO 1999 BMW 323IS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 BMW 323IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 BMW 323IS cars and light trucks from 1990+.
Anti-lock Brakes -> Description -> ABS Less Stability & Traction Control -> ABS w/Stability & Traction Control
Vehicle: 1999 BMW 323IS 2.5 L6 GAS
ABS Less Stability & Traction Control
The Anti-Lock Brake System (ABS) consists of a control unit, hydraulic unit, speed sensors and wiring harness, Fig. . Each speed sensor has a gear wheel which runs past the permanently magnetized edge of the speed sensor installed in the wheel hub. The rotary motion of the wheels is recorded by inductive sensors and an electric signal is sent to the electronic control unit.
The electronic control unit is located in a compartment on the right side of the engine compartment. This control unit inputs acceleration, deceleration and slip factors from ...
CLICK HERE TO GET FULL ACCESS TO 1999 BMW 323IS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 BMW 323IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 BMW 323IS cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> 1998 -> 1999-2000 -> 323Ci, 325, 328Ci & 330 & 2000 323i & 328i & 1999 323i & 328i Sedans -> Brake System Bleed -> Component Replacement -> Control Unit -> Front Speed Sensor -> Hydraulic Unit -> M3, Z3, 318, 323, 325, 328 & 330 -> M5, 525, 528, 530, 540, 740 & 750 -> Rear Speed Sensor -> X5 -> Z3, 318, 323is & 328is & 1998-99 M3, 328i & 1998 323i & 1999 323i & 328i Convertibles
Vehicle: 1999 BMW 323IS 2.5 L6 GAS
Brake System Bleed
Refer to "Hydraulic Brake Systems," for procedures.
Component Replacement
Hydraulic Unit
M3, Z3, 318, 323, 325, 328 & 330
Z3, 318, 323is & 328is & 1998-99 M3, 328i & 1998 323i & 1999 323i & 328i Convertibles
- Ensure ignition switch is in Off position.
- Remove Mass Air Flow (MAF) sensor from air filter housing.
- Disconnect cruise control drive motor as required.
- Remove brake fluid from master cylinder using suitable syringe.
- Disconnect central connector.
- Mark brake lines for installation alignment.
- Disconnect brake lines at master cylinder and hydraulic control unit.
- Disconnect s...
CLICK HERE TO GET FULL ACCESS TO 1999 BMW 323IS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 BMW 323IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 BMW 323IS cars and light trucks from 1990+.
Disc Brakes -> Description
Vehicle: 1999 BMW 323IS 2.5 L6 GAS
Refer to Figs. thro...
CLICK HERE TO GET FULL ACCESS TO 1999 BMW 323IS BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
![]() |
Access the Complete guide! |