Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Venture cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Caliper Service -> Assemble -> Blazer, Bravada & Jimmy -> Disassemble -> Front -> Inspection -> Installation -> Rear -> Removal -> Sierra & Silverado
Vehicle: 1999 Chevrolet Venture 3.4 V6 GAS
Removal
Front
- Siphon brake fluid out of master cylinder until fluid level is approximately 1/3 full, this will prevent fluid overflow when caliper piston is pushed back into its bore.
- Raise and support vehicle, then remove wheels.
- Push piston back into its bore using suitable C-clamp, Fig. .
- Remove two caliper mounting bolts and lift caliper off of rotor.
Rear
Blazer, Bravada & Jimmy
- Raise and support vehicle.
- Mark position of wheel to hub for installation reference.
- Remove wheel assembly.
- Remove mounting bolt and disconnect brake hose fitting from caliper. Discard gaskets and plug brake h...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Venture BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Venture cars and light trucks from 1990+.
Anti-lock Brakes -> Delphi Type VI -> Precautions -> Battery Ground Cable -> Delco LOC II -> General Service Precautions -> Radio Security System -> Theftlock
Vehicle: 1999 Chevrolet Venture 3.4 V6 GAS
Battery Ground Cable
Prior to service disconnect battery ground cable and isolate as required.
Radio Security System
Theftlock
If the Theftlock system is active when battery power is interrupted, the customers security code must be entered to restore proper function of the radio. To unlock a secured radio after power loss, proceed as follows:
- "LOC" appears with ignition in On position.
- Press "NM" and "000" will appear on display.
- Press "NM" again to make last two digits agree with security code.
- Press "HR" to make first 1 or 2 digits agree with security code.
- Press "AM-FM" to select code entered. "SEC" wi...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Venture BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Venture cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> Power Brake Unit Service
Vehicle: 1999 Chevrolet Venture 3.4 V6 GAS
The power brake unit is n...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Venture BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Venture cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Rotor Replacement -> 2WD Models -> 4WD Models -> Astro, Blazer, Bravada, Jimmy, K1500/2500 & T Series Pickup -> Except Montana, Silhouette, Trans Sport & Venture -> Front -> K3500 -> Montana, Silhouette, Trans Sport & Venture -> Rear
Vehicle: 1999 Chevrolet Venture 3.4 V6 GAS
2WD Models
Except Montana, Silhouette, Trans Sport & Venture
Front
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove caliper as outlined under "Caliper Service."
- Remove grease cap from hub/rotor, Fig. .
- Remove cotter pin, nut and washer.
- Remove hub/rotor from spindle, being careful not to damage spindle threads or outer bearing.
- Reverse procedure to install, noting the following:
- Apply high-temperature wheel bearing grease to inner and outer wheel bearings.
- Torque nut to 12 ft. lbs. while turning wheel assembly forward by hand, back nut off one flat or until hole in spindle...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Venture BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Venture cars and light trucks from 1990+.
Anti-lock Brakes -> Delphi Type VI -> Diagnosis & Testing -> 1997 -> 1997 Silhouette -> 1997 Tracker -> 1997 Trans Sport -> 1997 Venture -> 1998 -> 1998 Silhouette -> 1998 Tracker -> 1998 Trans Sport -> 1998 Venture -> 1998-99 -> 1999 Montana -> 1999 Silhouette -> 1999 Tracker -> 1999 Venture -> 1999-2001 -> 2000 Montana -> 2000 Silhouette -> 2000 Tracker -> 2000 Venture -> 2000-01 -> 20001 Venture -> 2001 Montana -> 2001 Silhouette -> 2001 Tracker -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Connector Pin ID -> Diagnosis Tests -> Diagnostic Trouble Code Interpretation -> Enhanced Diagnostics -> Intermittents & Poor Connections -> Montana, Silhouette, Trans Sport & Venture -> Temperature Vs. Resistance -> Tracker -> Wiring Diagrams
Vehicle: 1999 Chevrolet Venture 3.4 V6 GAS
Accessing Diagnostic Trouble Codes
Diagnostic trouble codes (DTCs) can only be read by connecting a suitably programmed scan tool to the Data Link Connector (DLC) and following the tool manufacturer instructions.
Diagnostic Trouble Code Interpretation
Refer to Figs. and , for Diagnostic Trouble Code (DTC) interpretation.
Wiring Diagrams
Refer to wiring diagrams in Vehicle Systems
Connector Pin ID
Montana, Silhouette, Trans Sport & Venture
Refer to Figs. and for connector pin identification.
Tracker
Refer to Figs. and , for connector pin identification.
Diagnosis Tests
1997 Silhouett...
[[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]]CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Venture BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Venture cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Astro, Bravada, S & T Series & Safari -> Aztek -> C & K Series -> Duo-Servo -> G Series -> Installation -> Montana, Silhouette, Trans Sport & Venture -> P Series -> Removal -> Single-Servo -> Tracker
Vehicle: 1999 Chevrolet Venture 3.4 V6 GAS
C & K Series
Duo-Servo
Removal
- Raise and support vehicle.
- Mark relationship of wheel to hub, then remove tire and wheel assembly.
- On models equipped with full-floating axles, remove hub and drum assembly as described in "Drive Axles."
- On models equipped with semi-floating axles, proceed as follows:
- Install pin into park brake lever.
- Mark relationship of drum to axle.
- Remove rear brake drum retainers, as required.
- Remove rear brake drum.
- On all models, remove return springs and shoe guide, Fig. .
- Remove brake hold down springs and pins.
- Disconnect actuator lever and pivot.
- Remove lever return spri...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Venture BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1999 Chevrolet Venture vehicle. |
Access the Complete guide! |