Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1999 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 KIA Sephia cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Replacement
Vehicle: 1999 KIA Sephia 1.8 L4 GAS
Replacement
- Remove master cylinder as outlined in "Hydraulic Brake Systems."
- Remove power brake unit in numbered sequence, Fig. .
- Reverse procedure to install, noting the following:
- Inspect all...
CLICK HERE TO GET FULL ACCESS TO 1999 KIA Sephia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 KIA Sephia cars and light trucks from 1990+.
Drum Brakes -> Inspection
Vehicle: 1999 KIA Sephia 1.8 L4 GAS
- Measure brake drum diameter. Ensure maximum diameter is within specifications.
- Inspect for scratches or...
CLICK HERE TO GET FULL ACCESS TO 1999 KIA Sephia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 KIA Sephia cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 1999 KIA Sephia 1.8 L4 GAS
- Ensure brake fluid reservoir remains at least 3/4 full during entire bleed procedure.
- Raise and support vehicle.
- Remove bleeder cap at bleeder screw farthest from master cylinder and attach a vinyl hose to bleeder screw.
- Place other end of tube in a clear container filled with fresh brake flui...
CLICK HERE TO GET FULL ACCESS TO 1999 KIA Sephia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 KIA Sephia cars and light trucks from 1990+.
Anti-lock Brakes -> Sephia & Spectra -> System Service -> 1997 -> 1998-2002 -> ABS Control Unit -> Brake System Bleed -> Component Replacement -> Front Wheel Speed Sensor -> Hydraulic Control Unit (HCU) -> Pump Motor & Main Relays -> Rear Wheel Speed Sensors
Vehicle: 1999 KIA Sephia 1.8 L4 GAS
Brake System Bleed
Refer to "Hydraulic Brake Systems" for brake bleeding procedure.
Component Replacement
ABS Control Unit
1997
- Remove front passenger seat.
- Release ABS control unit electrical connector latch, then disconnect harness.
- Remove ABS control unit four mounting screws, then the unit.
- Reverse procedure to install, noting the following:
- Torque ABS control unit mounting screws to 108-144 inch lbs.
- Torque front passenger seat bolts to 32-36 ft. lbs.
Hydraulic Control Unit (HCU)
- Disconnect HCU electrical connector.
- Disconnect pump motor connector from relay.
- Tag their locations, then disco...
CLICK HERE TO GET FULL ACCESS TO 1999 KIA Sephia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 KIA Sephia cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Brake Shoes, Replace -> Installation -> Removal -> Rio -> Sedona -> Sephia & Spectra -> Sportage
Vehicle: 1999 KIA Sephia 1.8 L4 GAS
Brake Shoes, Replace
Rio
- Remove brake shoes in numbered sequence, Fig. .
- Reverse procedure to install, noting the following:
- Clean backing plate with suitable vacuum cleaning equipment.
- Lubricate backing plate shoe contact pads.
- Tighten bolts and nuts to specifications.
Sedona
Removal
- Ensure parking brake is fully released.
- Raise and support vehicle.
- Remove tire and wheel.
- Remove brake drum to hub mounting screws, then the drum.
- Loosen parking brake cable square nut completely, Fig. .
- Remove adjuster spring from adjust lever and brake shoe, Fig. .
- Remove adjust lever, then rotate adjuster star...
CLICK HERE TO GET FULL ACCESS TO 1999 KIA Sephia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 KIA Sephia cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Master Cylinder -> Rio -> Sedona -> Sephia & Spectra -> Sportage
Vehicle: 1999 KIA Sephia 1.8 L4 GAS
Hydraulic brake fluid will damage painted surfaces. If fluid gets on painted surface, wipe clean immediately.
Master Cylinder
Rio
- Remove master cylinder in numbered sequence, Fig. , noting the following:
- Disconnect brake lines from master cylinder and ABS control unit using flare nut wrench tool No. OK130 430 019, or equivalent.
- Plug all open lines and ports to prevent entry of dirt or debris.
- Reverse procedure to install, noting the following:
- Place adjustment gauge tool No. OK370 430 018, or equivalent, onto master cylinder, Fig. .
- Apply 19.7 inches of vacuum to booster unit usi...
CLICK HERE TO GET FULL ACCESS TO 1999 KIA Sephia BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1999 KIA Sephia vehicle. |
Access the Complete guide! |