Auto Parts Search
2000 BMW 328I CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT BMW REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 2000 BMW 328I AUTOMOBILES
BMW -> Technical Service Bulletins -> Auxiliary Fan Does Not Operate At Low Speed Or Fuse Is Blown -> All Models
Vehicle: 2000 BMW 328I 2.8 L6 GAS
All Models
On some of these models the auxiliary fan may not operate at low speed or the fuse may be blown.
This condition may be cause by a defective low speed resistor.
To correct this condition, proceed as follows:
- On models with "BEHR" fan, disconnect...
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 BMW 328I AUTOMOBILES
Disc Brakes -> Caliper Service -> Assemble -> Disassemble -> Front -> Inspection -> Overhaul -> Rear -> Replace
Vehicle: 2000 BMW 328I 2.8 L6 GAS
Replace
Front
- Raise and support vehicle, then remove front tire and wheel.
- Press and hold brake pedal with suitable prop.
- Disconnect brake pipe from connection with hose.
- Remove wear indicator connector from lefthand side.
- Remove mounting bolts and caliper.
- Reverse procedure to install, noting the following:
- Tighten mounting bolts to specifications.
- Bleed brake system.
- Ensure brake pad wear sensor wire does not contact rotor or wheel.
Rear
- Raise and support vehicle, then remove rear tire and wheel assembly.
- Drain moderate amount of brake fluid from reservoir using suitable syringe.
- Disconnect...
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 2000 BMW 328I AUTOMOBILES
BMW -> Fuel Filter Scheduled Maintenance -> 1999-06
Vehicle: 2000 BMW 328I 2.8 L6 GAS
Inspection interval is determ...
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 BMW 328I AUTOMOBILES
DRIVESHAFT, Replace -> w/Rear Constant-Velocity Joint -> With Slide
Vehicle: 2000 BMW 328I 2.8 L6 GAS
w/Rear Constant-Velocity Joint
- Raise and support vehicle.
- Remove exhaust system and heat shield.
- Remove mounting bolts and exhaust suspension frame.
- Remove transmission joint disk mounting nuts.
- Remove mounting nuts and differential final drive flange constant-velocity joint.
- Remove center bearing mounting bolts. Do not allow propeller shaft to fall into joints.
- Bend propeller shaft downward at center mount and disconnect transmission or constant-velocity joint centering pin.
- Protect constant-velocity joint with suitable transport cap.
- Reverse procedure to install, noting the followi...
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2000 BMW 328I AUTOMOBILES
Component Replacement -> Installation -> Removal -> Tire Pressure Sensor
Vehicle: 2000 BMW 328I 2.8 L6 GAS
Tire Pressure Sensor
Removal
- Dismount tire using suitable tire machine ensuring not to damage tire pressure sensor.
- Remove the Torx screw, then the tire pressure sensor.
- Release valve stem union nut using removal tool No. 00 2 190, or equivalent Fig. .
- Remove washer from wheel.
Installation
- Install new Torx screw on tire pressure sensor, then twist new valve stem by hand approximately three turns. Do not tighten Torx screw, sensor and v...
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2000 BMW 328I AUTOMOBILES
Starter, Replace
Vehicle: 2000 BMW 328I 2.8 L6 GAS
- Remove air intake filter housing.
- Disconnect Mass Air Flow (MAF) sensor connector.
- Disconnect intake hose vacuum line and clip.
- Disconnect throttle cable from actuator by pulling it upward out of retainer and unhooking.
- Remove clamps, then the intake hose from throttle assembly and Idle Speed Control (ISC) valve.
- Remove lower engine covers, as required.
- Relieve fuel pressure as outlined in appropriate engine section.
- Remove fuel lines to ...
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2000 BMW 328I AUTOMOBILES
Cabin Air Filter Service -> BMW -> 1999-2005 3 Series & 2006 M3 & 325C Series
Vehicle: 2000 BMW 328I 2.8 L6 GAS
Service interval is determined by the service indicator.
- Open the hood.
- Turn the three cabin air filter cover retainers 1/4 turn.
- Remove the cabin air filter cover.
- Rotate the cabin filter cover retainers 45°, then ...
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2000 BMW 328I AUTOMOBILES
BMW -> Air Bag Warning Lamp ->
Vehicle: 2000 BMW 328I 2.8 L6 GAS
If the Air Bag warning lamp lights and stays on, diagnosis and ...
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2000 BMW 328I AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2000 BMW 328I 2.8 L6 GAS
Inlet
- Drain coolant into a suitable container.
- Reposition hose clamp at heater core and remove hose.
- Reposition hose clamp at water outlet and remove hose.
- Remove hose from vehicle.
- Reverse procedure to i...
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2000 BMW 328I AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2000 BMW 328I 2.8 L6 GAS
- Remove fan cowl by lifting out expansion rivets on both sides.
- Secure fan pulley with suitable securing tool, or equivalent, then remove fan. Fan has lefthand handed threads.
- Loosen tensioner lock bolts, then turn tensioner with suitable wrench to receive tens...
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2000 BMW 328I AUTOMOBILES
Component location diagrams for most 2000 BMW 328I cars and light trucks sold in the U.S. from 1990+.
Idle Speed Control Valve Diagram for 2000 BMW 328I 2.8 L6 GAS Components on diagram: |
Camshaft Position Sensor Diagram for 2000 BMW 328I 2.8 L6 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2000 BMW 328I AUTOMOBILES
OEM drawn wiring diagrams for most 2000 BMW 328I cars and light trucks sold in the U.S.
2000 BMW 328I 2.8 L6 GAS Wiring Diagram Components on diagram: |
2000 BMW 328I 2.8 L6 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2000 BMW 328I AUTOMOBILES
OEM TSB listings for most 2000 BMW 328I cars and light trucks sold in the U.S. from 1985+.
Document: Tools and Equipment Vehicle: 2000 BMW 328I 2.8 L6 GAS Auto Systems: |
Document: Tools and Equipment Vehicle: 2000 BMW 328I 2.8 L6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2000 BMW 328I AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2000 BMW 328I cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2000 BMW 328I cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2000 BMW 328I cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2000 BMW 328I cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2000 BMW 328I SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2000 BMW 328I vehicle. |
Access the Complete guide! |