Auto Parts Search
We have info for following modifications of 2000 Chevrolet Impala
- 2000 Chevrolet Impala 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:K
- 2000 Chevrolet Impala 3.4 V6 GAS, CID:207, Fuel Injection, Aspiration:207, Engine VIN:, Desg:E
- 2000 Chevrolet Impala LS 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:K
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2000 Chevrolet Impala AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2000 Chevrolet Impala cars and light trucks sold in the U.S. from mid 1990's+.
Reset Procedures -> 2000-05 Impala & Monte Carlo -> Using Light Switch
Vehicle: 2000 Chevrolet Impala 3.8 V6 GAS
2000-05 Impala & Monte Carlo
The Low Tire Pressure indicator will turn On when the pressure in one of the tires becomes 12 psi. lower or higher then the other three. The low tire pressure monitor system uses the ABS wheel speed sensors to determine if a tire is low by a variation in wheel speed.
- Inflate all tires to vehicle manufacturer's specifications.
- Place the ignition switch in the On position.
- Place radio in Off position.
- Press and hold DISP button until SETTINGS is displayed.
- Press the SEEK up or down buttons until TIRE MON is displayed.
- Press the PREV or NEXT buttons until RES...
CLICK HERE TO GET FULL ACCESS TO 2000 Chevrolet Impala TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2000 Chevrolet Impala AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2000 Chevrolet Impala cars and light trucks sold in the U.S. from mid 1990's+.
Component Locations
Vehicle: 2000 Chevrolet Impala LS 3.8 V6 GAS
Refer to Figs...
CLICK HERE TO GET FULL ACCESS TO 2000 Chevrolet Impala TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2000 Chevrolet Impala AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2000 Chevrolet Impala cars and light trucks sold in the U.S. from mid 1990's+.
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2000 Chevrolet Impala 3.4 V6 GAS
Refer to Fig. for wiring...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2000 Chevrolet Impala TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2000 Chevrolet Impala AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2000 Chevrolet Impala cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Diagnostic Tests -> Intermittent & Poor Connections -> Intermittents -> Poor Connections
Vehicle: 2000 Chevrolet Impala 3.4 V6 GAS
Accessing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to DLC (Data Link Connector) and follow manufacturer's instructions.
Diagnostic Tests
Refer to Figs. through for diagnostic test procedures.
Intermittent & Poor Connections
Intermittents
Most intermittents are caused by faulty electrical connections or wiring. Inspect for the following:
- Wiring broken inside insulation.
- Poor connection between male and female terminal at connector.
- Poor terminal to wire connection. Some conditions which fall under this are:
- Poor crimps.
- Poor solder joints.
- Crimping over wire ins...
CLICK HERE TO GET FULL ACCESS TO 2000 Chevrolet Impala TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2000 Chevrolet Impala AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2000 Chevrolet Impala cars and light trucks sold in the U.S. from mid 1990's+.
Reset Procedures -> 2000-05 Impala & Monte Carlo -> Using Light Switch
Vehicle: 2000 Chevrolet Impala 3.4 V6 GAS
2000-05 Impala & Monte Carlo
The Low Tire Pressure indicator will turn On when the pressure in one of the tires becomes 12 psi. lower or higher then the other three. The low tire pressure monitor system uses the ABS wheel speed sensors to determine if a tire is low by a variation in wheel speed.
- Inflate all tires to vehicle manufacturer's specifications.
- Place the ignition switch in the On position.
- Place radio in Off position.
- Press and hold DISP button until SETTINGS is displayed.
- Press the SEEK up or down buttons until TIRE MON is displayed.
- Press the PREV or NEXT buttons until RES...
CLICK HERE TO GET FULL ACCESS TO 2000 Chevrolet Impala TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2000 Chevrolet Impala AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2000 Chevrolet Impala cars and light trucks sold in the U.S. from mid 1990's+.
Reset Procedures -> 2000-05 Impala & Monte Carlo -> Using Light Switch
Vehicle: 2000 Chevrolet Impala LS 3.8 V6 GAS
2000-05 Impala & Monte Carlo
The Low Tire Pressure indicator will turn On when the pressure in one of the tires becomes 12 psi. lower or higher then the other three. The low tire pressure monitor system uses the ABS wheel speed sensors to determine if a tire is low by a variation in wheel speed.
- Inflate all tires to vehicle manufacturer's specifications.
- Place the ignition switch in the On position.
- Place radio in Off position.
- Press and hold DISP button until SETTINGS is displayed.
- Press the SEEK up or down buttons until TIRE MON is displayed.
- Press the PREV or NEXT buttons until RES...
CLICK HERE TO GET FULL ACCESS TO 2000 Chevrolet Impala TIRE PRESSURE MONITORING SYSTEM PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2000 Chevrolet Impala vehicle. |
Access the Complete guide! |