Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2000 Dodge Avenger car and truck
repair procedures including Dodge engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2000 Dodge Avenger automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2000 Dodge Avenger AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Dodge Avenger cars and light trucks from 1990+.
Disc Brakes -> Type 2 -> Caliper Service -> Overhaul -> Replacement
Vehicle: 2000 Dodge Avenger 2.5 V6 GAS
Replacement
- Remove brake pads, as outlined under "Brake Pad Service."
- Disconnect brake hose at brake caliper, then cap brake line.
- Reverse procedure to install.
Overhaul
- Remove caliper assembly as outlined under "Replacement."
- Remove caliper support, Fig. .
- Remove pin boots and boot ring.
- Position a suitable wood block in caliper body, then apply compressed air through brake hose fitting hole to remove piston and dust boot. Apply air gently.
- Remove piston seal using finger tip.
- Reverse procedure to assemble, noting following:
- Inspect cylinder and piston for wear, d...
CLICK HERE TO GET FULL ACCESS TO 2000 Dodge Avenger BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Dodge Avenger AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Dodge Avenger cars and light trucks from 1990+.
Hydraulic Brake Systems -> Adjustments -> Avenger & 1999-2000 Sebring Coupe -> Brake Booster Pushrod -> Stop Lamp Switch
Vehicle: 2000 Dodge Avenger 2.5 V6 GAS
Stop Lamp Switch
- Release stop lamp switch from bracket by rotating it 30° counterclockwise.
- Disconnect stop lamp switch wiring harness connector.
- Pull outward on stop lamp switch plunger until fully extended.
- Depress brake pedal, holding down in place.
- Install stop lamp switch onto bracket by aligning index key on switch with slot at top of square hole.
- Rotate switch 30° clockwise to lock switch into bracket, Fig. .
- Connect wiring harness connector to stop lamp switch.
- Pull back on brake pedal until pedal stops moving to allow switch plunger to ratchet to correct position.
Brake Booster Push...
CLICK HERE TO GET FULL ACCESS TO 2000 Dodge Avenger BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Dodge Avenger AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Dodge Avenger cars and light trucks from 1990+.
Hydraulic Brake Systems -> Tightening Specifications
Vehicle: 2000 Dodge Avenger 2.5 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2000 Dodge Avenger BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Dodge Avenger AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Dodge Avenger cars and light trucks from 1990+.
Anti-lock Brakes -> Bosch Anti-Lock Braking System -> Troubleshooting
Vehicle: 2000 Dodge Avenger 2.5 V6 GAS
Refer to flow charts under "Symptom Based Diagnosis" unde...
CLICK HERE TO GET FULL ACCESS TO 2000 Dodge Avenger BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Dodge Avenger AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Dodge Avenger cars and light trucks from 1990+.
Disc Brakes -> Type 2 -> Tightening Specifications
Vehicle: 2000 Dodge Avenger 2.5 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2000 Dodge Avenger BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Dodge Avenger AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Dodge Avenger cars and light trucks from 1990+.
Hydraulic Brake Systems -> Diagnosis & Testing -> 1999-2000 -> Avenger -> Breeze & Cirrus -> Concorde, Intrepid, LHS & 300M -> Convertible -> Coupe -> Less ABS -> Less Anti-Lock Brake System -> Neon -> Proportioning Valve -> Sebring & Stratus -> Sedan -> With ABS -> With Anti-Lock Brake System
Vehicle: 2000 Dodge Avenger 2.5 V6 GAS
Proportioning Valve
Avenger
- Install suitable pressure gauges, one each on input side and output side of proportioning valve.
- Bleed brake line and pressure gauge, then gradually depress brake pedal and observe gauge.
- Observe left and righthand output pressures.
- Pressure difference between left and right sides should not be more than 57 psi.
- Refer to "Hydraulic Brake Control Specifications."
- If pressure is not within specifications, replace proportioning valve.
Breeze & Cirrus
Less Anti-Lock Brake System
- Road test vehicle to determine which rear wheel exhibits premature wheel skid.
- Remove ...
CLICK HERE TO GET FULL ACCESS TO 2000 Dodge Avenger BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2000 Dodge Avenger vehicle.
|
| Access the Complete guide! |
