Auto Parts Search
We have info for following modifications of 2000 Ford Mustang
- 2000 Ford Mustang 3.8 V6 GAS, CID:232, Fuel Injection, Aspiration:232, Engine VIN:, Desg:4
- 2000 Ford Mustang GT 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:X
- 2000 Ford Mustang SVT Cobra R 5.4 V8 GAS, CC:5409, CID:330, Fuel Injection, Aspiration:330, Engine VIN:, Desg:H
BRAKE SERVICE PROCEDURES FOR 2000 Ford Mustang AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Ford Mustang cars and light trucks from 1990+.
Disc Brakes -> Front Disc Brakes -> Rotor Replacement -> Installation -> Removal
Vehicle: 2000 Ford Mustang 3.8 V6 GAS
If caliper does not require servicing, do not disconnect brake hose or remove caliper from vehicle. Position caliper aside with wire or tie straps to avoid damaging caliper or hose.
If excessive force must be used to remove the rotor, then it should be inspected for lateral runout before installation.
Removal
- On models equipped with air suspension, turn service switch Off.
- On all models, raise and support vehicle, then remove wheel and tire assembly. Use care to avoid damage or interference with caliper bleeder screw fitting and brake rotor shield.
- Remove caliper anchor bracket bol...
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Mustang BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Ford Mustang AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Ford Mustang cars and light trucks from 1990+.
Disc Brakes -> Rear Disc & Parking Brakes -> Tightening Specifications
Vehicle: 2000 Ford Mustang GT 4.6 V8 GAS
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Mustang BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Ford Mustang AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Ford Mustang cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Disassemble -> Inspection -> Master Cylinder Overhaul -> Overhaul -> Wheel Cylinders
Vehicle: 2000 Ford Mustang 3.8 V6 GAS
Master Cylinder Overhaul
Disassemble
- Clean outside of master cylinder thoroughly. Drain brake fluid from master cylinder.
- Remove stop bolt and pressure control valves, if equipped.
- Pry up on reservoir and remove it from master cylinder body.
- Remove fluid control valve, if equipped.
- Depress primary piston and remove snap ring from retaining groove at open end of bore.
- Remove primary and secondary piston assemblies from master cylinder. If secondary piston does not come out, apply air pressure to secondary outlet port to remove.
Inspection
When disassembled, wash all parts in clean brake...
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Mustang BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Ford Mustang AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Ford Mustang cars and light trucks from 1990+.
Disc Brakes -> Rear Disc & Parking Brakes -> Adjustments -> Continental -> Contour & Mystique -> Cougar, Crown Victoria, Grand Marquis, Marauder & Town Car -> Escort, Tracer & ZX2 -> Mustang -> Parking Brake -> Sable & Taurus
Vehicle: 2000 Ford Mustang 3.8 V6 GAS
Parking Brake
Cougar, Crown Victoria, Grand Marquis, Marauder & Town Car
- Apply parking brake control fully with 100 lbs., foot pedal effort, then release brake control.
- Place transmission in Neutral, then raise and support vehicle.
- With parking brake control in Off position, grasp pensioner around housing. Using an hook tool place end into rounded end of clip between clip and housing. Unlock clip by pulling downward with tool and support pensioner.
- The pensioner spring will take up cable slack and reload cables, while holding pensioner, lock clip by pushing up on bottom of clip. If clip ...
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Mustang BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Ford Mustang AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Ford Mustang cars and light trucks from 1990+.
Power Brake Units -> Troubleshooting -> Bendix Diaphragm Types -> Bendix Hydro-Boost Type -> Brakes Grab -> Erratic Booster Operation, Binding, Grabbing Or Sticking -> Hard Pedal Or No Assist -> No Or Slow Release -> No Power Assist
Vehicle: 2000 Ford Mustang GT 4.6 V8 GAS
Complaints about power brake operation should be handled as if two separate systems exist. Inspect for faults in the hydraulic system first. If it is satisfactory, start inspecting the power brake circuit. For a quick inspection of proper power unit operation, press the brake pedal firmly and then start the engine. The pedal should fall away slightly and less pressure should be needed to maintain the pedal in any position.
Another inspection begins with installation of a suitable pressure gauge in the brake hydraulic system. Take a reading with the engine Off and the power unit n...
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Mustang BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Ford Mustang AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Ford Mustang cars and light trucks from 1990+.
Anti-lock Brakes -> Mustang -> Precautions -> Fuel System Pressure Relief -> Hydraulic Brake Fluid Color
Vehicle: 2000 Ford Mustang 3.8 V6 GAS
Fuel System Pressure Relief
Fuel supply tubes will remain pressurized for long periods of time after engine shutdown. This pressure must be relieved before performing fuel system service. A valve is provided on the fuel injection supply manifold for this purpose.
- Remove air cleaner assembly.
- Connect EFI and CFI fuel pressure gauge tool No. T80L-9974-B, or equivalent, to fuel pressure relief valve cap on fuel injection supply manifold.
- Open manual valve on gauge tool to relieve fuel system pressure.
Hydraulic Brake Fluid Color
Hydraulic brake fluid must conform with the requirements of Fed...
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Mustang BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2000 Ford Mustang vehicle. |
Access the Complete guide! |