Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2000 Ford Windstar car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2000 Ford Windstar automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2000 Ford Windstar
- 2000 Ford Windstar 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:U
- 2000 Ford Windstar 3.8 V6 GAS, CID:232, Fuel Injection, Aspiration:232, Engine VIN:, Desg:4
A/C & HEATER SERVICE PROCEDURES FOR 2000 Ford Windstar AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported 2000 Ford Windstar cars and light trucks from 1990+
Component Replacement & Adjustment -> Light Duty Trucks & Vans -> Vacuum Motor, Replace -> 1998 Windstar -> 1999-2000 Windstar -> Air Damper -> Air Inlet -> Econoline -> Excursion -> Expedition & Navigator -> Explorer & Mountaineer -> F-Series -> Floor/Defrost -> Panel Door -> Panel/Defrost -> Panel/Floor -> Ranger -> Recirculate/Fresh -> Windshield Defroster
Vehicle: 2000 Ford Windstar 3.0 V6 GAS
Econoline
Floor/Defrost
- Remove access panel, Fig. .
- Remove actuator vacuum lines, Fig. .
- Remove actuator mounting screws then lift up on vacuum control motor arm to disengage it from door crank.
- Remove vacuum control motor.
- Reverse procedure to install.
Panel Door
- Remove access panel, Fig. .
- Remove vacuum line from actuator, Fig. .
- Remove mounting screws, then lift up on vacuum motor arm to disengage it from door crank, Fig. .
- Remove vacuum motor.
- Reverse procedure to install.
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Windstar A/C & HEATER SERVICE PROCEDURES
A/C & HEATER SERVICE PROCEDURES FOR 2000 Ford Windstar AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported 2000 Ford Windstar cars and light trucks from 1990+
Air Bag System Precautions -> Ford Motor Co. -> Arming -> 1990-91 -> 1990-92 -> 1991-92 -> 1992-93 -> 1992-94 -> 1992-96 -> 1992-98 -> 1993 -> 1993-94 -> 1993-95 -> 1994 -> 1994-95 -> 1994-96 -> 1994-97 -> 1995 -> 1995-2004 -> 1995-96 -> 1995-98 -> 1996-97 -> 1996-99 -> 1997-2000 -> 1997-2001 -> 1997-2004 -> 1997-99 -> 1998 -> 1998-2000 -> 1998-2002 -> 1999-2000 -> 1999-2001 -> 1999-2002 -> 1999-2004 -> 2000 -> 2000-01 -> 2000-04 -> 2001-02 -> 2001-03 -> 2001-04 -> 2002-03 -> 2002-04 -> 2004 -> Aerostar & Bronco -> Aspire -> Aviator -> Blackwood, Expedition & Navigator -> Built After February 2002 -> Built Before March 2002 -> Capri -> Continental -> Contour & Mystique -> Cougar -> Crown Victoria Grand Marquis & Marauder -> Econoline -> Escape -> Escort, Tracer & ZX2 -> Excursion -> Explorer & Mountaineer -> Explorer Sport & Sport Trac -> F Series -> Focus -> Freestar & Monterey -> Light Trucks & Vans -> LS -> Mark VII -> Mark VIII -> Mustang -> Passenger Cars -> Probe -> Ranger -> Sable & Taurus -> Tempo & Topaz -> Thunderbird -> Town Car -> Villager -> Windstar
Vehicle: 2000 Ford Windstar 3.0 V6 GAS
Passenger Cars
Aspire
- Disconnect battery ground cable.
- Wait one minute for back-up power supply to deplete stored energy.
- Remove restraint system diagnostic tool from driver's side air bag module electrical connector.
- Connect driver's side air bag module electrical connector.
- Install driver's side air bag module as outlined under "Component Service."
- Remove restraint system diagnostic tool from passenger's side air bag module electrical connector.
- Install passenger's side air bag module as outlined under "Component Service."
- C...
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Windstar A/C & HEATER SERVICE PROCEDURES
A/C & HEATER SERVICE PROCEDURES FOR 2000 Ford Windstar AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported 2000 Ford Windstar cars and light trucks from 1990+
Compressor Service -> Thermal Protection Switch, Replace -> Installation -> Removal -> SD-7H15
Vehicle: 2000 Ford Windstar 3.0 V6 GAS
SD-7H15
Removal
- Remove retaining plate and wire guide retaining bolt, then the retaining plate.
- Use a small flat bladed screwdriver to break thermal switch silicone seal, then pry switch from cover, Fig. .
- Discard thermal switch and clean sealer from opening of compressor.
Instal...
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Windstar A/C & HEATER SERVICE PROCEDURES
A/C & HEATER SERVICE PROCEDURES FOR 2000 Ford Windstar AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported 2000 Ford Windstar cars and light trucks from 1990+
Component Replacement & Adjustment -> Light Duty Trucks & Vans -> Water Pump, Replace -> 1998 -> 1999-2000 -> 2.5L Engine -> 3.0L Engine -> 3.8L Engine -> 4.0L Engine -> 4.0L Pushrod Engine -> 4.0L SOHC Engine -> 4.2L Engine -> 4.6L, 5.4L & 6.8L Engines -> 5.0L Engine -> 7.3L Diesel Engine -> Diesel Engine -> Econoline -> Excursion -> Expedition & Navigator -> Explorer & Mountaineer -> F-Series -> Gasoline Engine -> Ranger -> Villager -> Windstar
Vehicle: 2000 Ford Windstar 3.8 V6 GAS
Econoline
4.2L Engine
- Drain coolant into suitable container.
- Remove fan and fan clutch.
- Remove accessory drive belt.
- Remove lower radiator hose from water pump.
- Disconnect engine harness from water pump mounting stud and water bypass tube.
- Remove A/C compressor support bracket.
- Remove bolts and pulley from water pump.
- Remove bypass tube from water pump.
- Remove bolts (A) and stud bolts (B), Fig. , from water pump, then remove pump from cover.
- Reverse procedure to install, noting the following:
-
...
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Windstar A/C & HEATER SERVICE PROCEDURES
A/C & HEATER SERVICE PROCEDURES FOR 2000 Ford Windstar AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported 2000 Ford Windstar cars and light trucks from 1990+
Compressor Service -> Compressor Clutch Service -> Clutch Field Coil, Replace -> Clutch Hub & Pulley, Replace -> FS-10 & SC90V -> Installation -> Removal -> SD-7H15
Vehicle: 2000 Ford Windstar 3.0 V6 GAS
Clutch Hub & Pulley, Replace
FS-10 & SC90V
Removal
- Holding clutch plate with a suitable spanner wrench, Figs. and , remove clutch hub retaining nut or bolt, Figs. through .
- On models where clutch plate is retained with a nut, remove clutch hub and shims from compressor shaft using hub remover tool No. T94P-19703-AH, or equivalent, Fig. .
- On models where clutch plate is retained by a bolt, lift assembly and shims from compressor. If necessary, thread a suitable bolt into clutch plate hub to break hub free of shaft, Fig. . ...
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Windstar A/C & HEATER SERVICE PROCEDURES
A/C & HEATER SERVICE PROCEDURES FOR 2000 Ford Windstar AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported 2000 Ford Windstar cars and light trucks from 1990+
Air Bag System Precautions -> Ford Motor Co. -> Arming -> 1990-91 -> 1990-92 -> 1991-92 -> 1992-93 -> 1992-94 -> 1992-96 -> 1992-98 -> 1993 -> 1993-94 -> 1993-95 -> 1994 -> 1994-95 -> 1994-96 -> 1994-97 -> 1995 -> 1995-2004 -> 1995-96 -> 1995-98 -> 1996-97 -> 1996-99 -> 1997-2000 -> 1997-2001 -> 1997-2004 -> 1997-99 -> 1998 -> 1998-2000 -> 1998-2002 -> 1999-2000 -> 1999-2001 -> 1999-2002 -> 1999-2004 -> 2000 -> 2000-01 -> 2000-04 -> 2001-02 -> 2001-03 -> 2001-04 -> 2002-03 -> 2002-04 -> 2004 -> Aerostar & Bronco -> Aspire -> Aviator -> Blackwood, Expedition & Navigator -> Built After February 2002 -> Built Before March 2002 -> Capri -> Continental -> Contour & Mystique -> Cougar -> Crown Victoria Grand Marquis & Marauder -> Econoline -> Escape -> Escort, Tracer & ZX2 -> Excursion -> Explorer & Mountaineer -> Explorer Sport & Sport Trac -> F Series -> Focus -> Freestar & Monterey -> Light Trucks & Vans -> LS -> Mark VII -> Mark VIII -> Mustang -> Passenger Cars -> Probe -> Ranger -> Sable & Taurus -> Tempo & Topaz -> Thunderbird -> Town Car -> Villager -> Windstar
Vehicle: 2000 Ford Windstar 3.8 V6 GAS
Passenger Cars
Aspire
- Disconnect battery ground cable.
- Wait one minute for back-up power supply to deplete stored energy.
- Remove restraint system diagnostic tool from driver's side air bag module electrical connector.
- Connect driver's side air bag module electrical connector.
- Install driver's side air bag module as outlined under "Component Service."
- Remove restraint system diagnostic tool from passenger's side air bag module electrical connector.
- Install passenger's side air bag module as outlined under "Component Service."
- C...
CLICK HERE TO GET FULL ACCESS TO 2000 Ford Windstar A/C & HEATER SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
