Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 2000 Infiniti I30 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Infiniti I30 cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> 1999 -> 2000-02 -> Actuator -> Actuator Relays -> Brake System Bleed -> Component Replacement -> Front -> G20 -> G20, I30 & I35 -> I30 & I35 -> I35 -> J30 -> J30 & Q45 -> Q45 -> Rear -> Speed Sensors -> Speed Sensors Rotor -> VDC/TCS/ABS Control Module -> Yaw Rate/G Sensor
Vehicle: 2000 Infiniti I30 3.0 V6 GAS
Brake System Bleed
Refer to "Hydraulic Brake System" for procedure.
Component Replacement
Speed Sensors
- Disconnect wiring connector.
- Remove mounting bolt and sensor, Figs. through .
- Reverse procedure to install, noting the following:
- On G20 and I30 models, torque front wheel sensor mounting bolts to 13-17 ft. lbs.
- On G20 and I30 models, torque rear wheel sensor mounting bolts to 18-25 ft. lbs.
- On J30 & Q45 models, torque wheel sensor mounting bolts to 96-132 inch lbs.
Speed Sensors Rotor
G20, I30 & I35
Front
- Remove drive shaft as outlined in "Front Wheel Drive Axles."
- Remove sensor rotor using su...
CLICK HERE TO GET FULL ACCESS TO 2000 Infiniti I30 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Infiniti I30 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Infiniti I30 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 2000 Infiniti I30 3.0 V6 GAS
Do not spill brake fluid on painted surfaces, it may cause damage to the paint. If brake fluid is spilled, wash immediately with water.
- Place container under master cylinder to avoid spillage, then fill master cylinder with brake fluid.
- Connect hose to bleeder valves and depress brake pedal several times.
- With pressure applied to pedal...
CLICK HERE TO GET FULL ACCESS TO 2000 Infiniti I30 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Infiniti I30 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Infiniti I30 cars and light trucks from 1990+.
Power Brake Units -> Troubleshooting
Vehicle: 2000 Infiniti I30 3.0 V6 GAS
- With engine off, depress brake pedal several times. There should be no change in pedal stroke.
- With brake pedal depressed, start engine. Pedal should go down slightly.
- Run engine for two minutes, then turn engine off.
- Depress brake pedal slowly several t...
CLICK HERE TO GET FULL ACCESS TO 2000 Infiniti I30 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Infiniti I30 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Infiniti I30 cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Cylinder Body -> Front -> G20, I30 & I35 -> Inspection -> J30 & Q45 -> Overhaul -> Piston -> Rear -> Replacement
Vehicle: 2000 Infiniti I30 3.0 V6 GAS
Replacement
Front
- Raise and support vehicle.
- Remove caliper mounting pins/bolts, Figs. through .
- Disconnect brake hose and remove caliper.
- Reverse procedure to install.
Rear
- Raise and support vehicle.
- Remove brake cable mounting bolt and lock spring.
- Disconnect parking brake control lever and cable.
- Remove caliper mounting pins/bolts, Figs. through .
- Disconnect brake hose and remove caliper.
- Reverse procedure to install.
Overhaul
Front
- Push out piston with dust seal by blowing compressed air through brake hose hole.
- Remove piston seal using suitable tool.
- Reverse procedure to assemble.
Rear
G20,...
CLICK HERE TO GET FULL ACCESS TO 2000 Infiniti I30 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Infiniti I30 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Infiniti I30 cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 2000 Infiniti I30 3.0 V6 GAS
The vacuum assist diaphragm assembly multiplies the force exerted on the master cylinder piston in order to increase the hydraulic pressure delivered to the wheel calipers while decreasing the effort necessary to obtain acceptable stopping performance.
Vacuum assist units get their energy by opposing engine vacuum to atmospheric pressure. A piston, cylinder and f...
CLICK HERE TO GET FULL ACCESS TO 2000 Infiniti I30 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Infiniti I30 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Infiniti I30 cars and light trucks from 1990+.
Anti-lock Brakes -> Diagnosis & Testing -> 1997 -> 1997-2001 -> 1997-98 -> 1998-2000 -> 1998-2001 -> 1999 -> 1999-2001 -> 2000-01 -> 2001 -> 2002 -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Component Testing -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation -> G20 -> I30 -> I35 -> J30 -> Less Scan Tool -> Preliminary Check -> Q45 -> Symptom Based Tests -> Wiring Diagram -> With Scan Tool -> With TCS -> With VDC
Vehicle: 2000 Infiniti I30 3.0 V6 GAS
Accessing Diagnostic Trouble Codes
With Scan Tool
Turn ignition switch to Off position.
Connect CONSULT-II, or suitably programmed scan tool, to Data Link Connector (DLC).
Start engine.
Drive vehicle at more than 19 mph for at least one minute.
Stop vehicle with engine running and follow tool manufacturer's instructions.
Less Scan Tool
Drive vehicle at more than 19 mph for at least one minute.
Turn ignition switch to Off position.
On J30, 1997-99 I30, Q45 and 1999 G20 models, ground Data Link Connector (DLC) terminal No. 4 using suitable harness.
On 2000-02 G20 and 2000 Q45 models, gro...
[[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]] [[table data]]CLICK HERE TO GET FULL ACCESS TO 2000 Infiniti I30 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2000 Infiniti I30 vehicle. |
Access the Complete guide! |