Auto Parts Search
2000 Jaguar S-TYPE CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Jaguar REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service

A/C & HEATER SERVICE PROCEDURES FOR 2000 Jaguar S-TYPE AUTOMOBILES
Import Compressor Service -> Nippondenso Compressor -> Precautions -> Product Compatibility
Vehicle: 2000 Jaguar S-TYPE 4.0 V8 GAS
Product Compatibility
Before replenishing refrigerant or refrigerant oil, en...
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Jaguar S-TYPE AUTOMOBILES
Anti-lock Brakes -> Diagnosis & Testing -> 1285: Booster Solenoid Output Circuit Failure -> Accessing Diagnostic Trouble Codes -> B1342: ABS Control Module Fault -> B1342: CAN Circuit Failure -> B1342: DSC Control Module Fault -> B1485: Stop Lamp Switch Input Circuit Short To Positive Voltage -> B1676: Battery Voltage Out Of Range -> C1095: Hydraulic Pump Motor Circuit Failure -> C1137: Control Module Internal Circuit Failure -> C1145: Wheel Speed Sensor Circuit Righthand Front Electrical Failure -> C1155: Wheel Speed Sensor Circuit Lefthand Front Electrical Failure -> C1165: Wheel Speed Sensor Circuit Righthand Rear Electrical Failure -> C1175: Wheel Speed Sensor Circuit Lefthand Rear Electrical Failure -> C1233: Wheel Speed Sensor Circuit Lefthand Front Signal Failure -> C1234: Wheel Speed Sensor Circuit Righthand Front Signal Failure -> C1235: Wheel Speed Sensor Circuit Righthand Rear Signal Failure -> C1236: Wheel Speed Sensor Circuit Lefthand Rear Signal Failure -> C1267: Modulator Valve Failure -> C1277: Steering Wheel Angle 1 & 2 Circuit Failure -> C1278: Steering Wheel Angle 1 & 2 Signal Fault -> C1279: Yaw Rate Sensor Circuit Failure -> C1280: Yaw Rate Sensor Signal Fault -> C1281: Lateral Accelerometer Circuit Failure -> C1282: Lateral Accelerometer Signal Failure -> C1286: Booster Mechanical Fault -> C1287: Booster Pedal Force Switch Circuit Failure -> C1288: Pressure Transducer Main/Primary Input Circuit Failure -> C1289: Pressure Transducer Redundant/Secondary Input Circuit Failure -> C1730: Reference Voltage Out Of Range -> Check Booster Solenoid Output Circuits For Shorts To Ground -> Check Brake Booster Solenoid -> Check Brake Booster Solenoid Circuit For Short To Ground -> Check Brake Booster Vacuum Pipe -> Check Brake Booster Voltage Supply Circuit For Short To Ground -> Check Condition Of Fuse -> Check Continuity Of Booster Solenoid Output Circuits -> Check Continuity Of Brake Booster Solenoid Circuit -> Check Continuity Of Brake Booster Voltage Supply Circuit -> Check Continuity Of Brake Lamp Switch -> Check Continuity Of DSC Sensor Reference Voltage Supply Circuit -> Check Continuity Of Lateral Accelerometer Signal Ground Circuit -> Check Continuity Of Lateral Accelerometer Signal Input Circuit -> Check Continuity Of Lateral Accelerometer Supply Circuit -> Check Continuity Of Pressure Transducer Primary Input Circuit -> Check Continuity Of Steering Wheel Angle Sensor Ground Supply Circuit -> Check Continuity Of Wheel Angle 1 & 2 Signal Circuit -> Check Continuity Of Yaw Rate Sensor Signal Ground Circuit -> Check Continuity Of Yaw Rate Sensor Signal Input Circuit -> Check Continuity Of Yaw Rate Sensor Supply Circuit -> Check DSC Sensor Reference Voltage -> Check DSC Sensor Reference Voltage Supply Circuit For Short To Ground -> Check Electrical Continuity (1) (Ignition Off) -> Check Electrical Continuity (2) (Ignition Off) -> Check For Short Circuit (1) (Ignition Off) -> Check For Short Circuit (2) (Ignition On) -> Check For Short To B+ -> Check For Short To Ignition -> Check Ground Supply To ABS Control Module -> Check Ground Supply To DSC Control Module -> Check Harness Short Core To Core -> Check Harness Short To Ground -> Check Harness Signal Continuity -> Check Lateral Accelerometer Signal Ground Circuit For Short To Ground -> Check Lateral Accelerometer Signal Input Circuit For Short To Ground -> Check Lateral Accelerometer Supply Circuit For Short To Ground -> Check Pressure Transducer Primary Input Circuit For Shorts To Ground -> Check Pressure Transducer Secondary Input Circuit For Shorts To Ground -> Check Resistance Of ABS Or DSC Hydraulic Pump -> Check Sensor Continuity -> Check Sensor Output -> Check Steering Wheel Angle 1 & 2 Sensor Signal -> Check Steering Wheel Angle Sensor Ground Supply Circuit -> Check Steering Wheel Angle Sensor Ground Supply Circuit For Short To Ground -> Check Stop Lamp Switch Circuit For Short To Positive Voltage -> Check Voltage Supply Between Fuse 14 At Front Power Distribution Box -> Check Voltage Supply From Fuse 14 At Front Power Distribution Box -> Check Voltage Supply From Fuse 22 At Front Power Distribution Box -> Check Voltage Supply From Fuse 3 At Primary Junction Box -> Check Voltage Supply From Primary Junction Box To Steering Wheel Angle Sensor Circuit+ -> Check Voltage Supply To ABS Control Module -> Check Voltage Supply To Brake Booster -> Check Voltage Supply To DSC Control Module -> Check Voltage Supply To Steering Wheel Angle Sensor Circuit -> Check Wheel Angle 1 & 2 Signal Circuit For Short To Ground -> Check Wheel Speed Sensor Resistance -> Check Yaw Rate Sensor Signal Ground Circuit For Short To Ground -> Check Yaw Rate Sensor Signal Input Circuit For Short To Ground -> Check Yaw Rate Sensor Supply Circuit For Short To Ground -> Clearing Diagnostic Trouble Codes -> Component Locations -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation -> Inspect Harness/Connectors -> Measure Connector Resistance -> Measure Connector Resistance (Ignition Off) -> Measure Connector Voltage -> Measure VREF Voltage At Pressure Transducer Main Input Circuit Electrical Connector -> Measure VREF Voltage At Pressure Transducer Redundant Input Circuit Electrical Connector -> Mechanical Check -> S Type -> S Type Less DSC -> S Type w/DSC -> Wiring Diagrams -> XJR, XJ8, XKR & XK8
Vehicle: 2000 Jaguar S-TYPE 4.0 V8 GAS
Accessing Diagnostic Trouble Codes
Diagnostic Trouble Codes (DTCs) are accessed by connecting a suitable programmed scan tool to the Data Link Connector (DLC) and following the tool manufacturer's instructions. The DLC is located on the instrument panel adjacent to the driver's side A-pillar.
Diagnostic Trouble Code Interpretation
Refer to Figs. and for Diagnostic Trouble Code (DTC) interpretation.
Component Locations
Refer to Figs. and for component locations.
Wiring Diagrams
Refer toFigs. through for wiring diagrams.
Diagnostic Tests
B1342: ABS Control Module Fault
S Type
Check...
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 2000 Jaguar S-TYPE AUTOMOBILES
Jaguar -> Fuel Filter Scheduled Maintenance -> 1997-2006 S-Type, XJ8, XJR, XK8 & XKR -> Normal Service -> Severe Service
Vehicle: 2000 Jaguar S-TYPE 3.0 V6 GAS
Normal Service
Replace...
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Jaguar S-TYPE AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2000 Jaguar S-TYPE 3.0 V6 GAS
- Raise and support vehicle, then remove rear tire and wheel assemblies.
- Remove axle shaft hub nut.
- Disconnect brake caliper.
- Disconnect harness and ABS sensor.
- Disconnect outer tie rod.
- Disconnect lower arm from hub assembly.
- Remove brake disc.
- Disconnect hub assembly from driveshaft.
- Disconnect axle shaft from differential housing using suitable pry tool. Do not damage differential seal.
- Remove axle shaft from differential housing. Do not loosen or remove flexible coupling.
- Mark driveshaft to flange for installation alignment.
- Mark balance nut to flange for installation alignment.
- Mark ...
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2000 Jaguar S-TYPE AUTOMOBILES
Starter, Replace
Vehicle: 2000 Jaguar S-TYPE 4.0 V8 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- Remove electrical connector protective cover.
- Disconnect starter motor electrical connectors.
- Remove oxygen sensor.
- Detach oxygen sensor harness electrical conne...
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2000 Jaguar S-TYPE AUTOMOBILES
Cabin Air Filter Service -> Jaguar -> 2000-08 S-Type
Vehicle: 2000 Jaguar S-TYPE 4.0 V8 GAS
Under normal operating conditions the cabin air filter should be replaced every 10,000 miles. In dusty areas change the cabin air filter more often.
- Open the hood.
- Note position of the windshield wiper blades on the windshield.
- Remove the windshield wiper arm nut covers.
- Remove the windshield wiper arm retaining nuts, then remove the wiper arms using a suitable windshield wiper arm puller.
- Remove the cowl grille screw covers.
- Remove the cowl grille screws and retaine...
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2000 Jaguar S-TYPE AUTOMOBILES
Jaguar -> Check Engine Lamp -> 1995-2009
Vehicle: 2000 Jaguar S-TYPE 3.0 V6 GAS
The Check Engine warning lamp is used to warn of a system fault. It will be lit during engine start-up, but should go out when the self-diagnostic system determines that the system is functioning properly. I...
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2000 Jaguar S-TYPE AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2000 Jaguar S-TYPE 4.0 V8 GAS
Inlet
- Drain coolant into a suitable container.
- Remove air intake tube.
- Remove wiper arms.
- Remove cowl grille.
- Remove engine compartment brace.
- Disconnect heater hoses from heater core.
- Disconnect three quick-disconnect couplings from coolant control valves hoses.
- Disconnect coolant recovery line.
- Detach heater hose assembly bracket.
- Raise and support vehicle.
- Remove bolt and disengage push connector.
- Lower vehicle.
- Remove hose assembly from vehicle.
- Reverse procedure t...
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2000 Jaguar S-TYPE AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2000 Jaguar S-TYPE 4.0 V8 GAS
- Install suitable spanner wrench tool, on belt tensioner pulley center bolt.
- Turn tool counterclo...
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2000 Jaguar S-TYPE AUTOMOBILES
Component location diagrams for most 2000 Jaguar S-TYPE cars and light trucks sold in the U.S. from 1990+.
![]() Components on diagram: |
![]() Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2000 Jaguar S-TYPE AUTOMOBILES
OEM drawn wiring diagrams for most 2000 Jaguar S-TYPE cars and light trucks sold in the U.S.
![]() Components on diagram: |
![]() Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2000 Jaguar S-TYPE AUTOMOBILES
OEM TSB listings for most 2000 Jaguar S-TYPE cars and light trucks sold in the U.S. from 1985+.
Document: UNABLE TO REDUCE CLIMATE CONTROL OUTLET TEMPERATURE - DIAGNOSTIC PROCEDURE Vehicle: 2000 Jaguar S-TYPE 3.0 V6 GAS Auto Systems: |
Document: UNABLE TO LOCK VEHICLE WITH REMOTE KEY FOB - REPAIR PROCEDURE Vehicle: 2000 Jaguar S-TYPE 3.0 V6 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2000 Jaguar S-TYPE AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2000 Jaguar S-TYPE cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2000 Jaguar S-TYPE cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2000 Jaguar S-TYPE cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2000 Jaguar S-TYPE cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2000 Jaguar S-TYPE SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
![]() |
Access the Complete guide! |