Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2000 Jeep Grand Cherokee car and truck
repair procedures including Jeep engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2000 Jeep Grand Cherokee automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2000 Jeep Grand Cherokee
- 2000 Jeep Grand Cherokee Laredo 4.0 L6 GAS, CID:242, Fuel Injection, Aspiration:242, Engine VIN:, Desg:S
- 2000 Jeep Grand Cherokee Laredo 4.7 V8 GAS, CID:287, Fuel Injection, Aspiration:287, Engine VIN:, Desg:N
- 2000 Jeep Grand Cherokee Limited 4.0 L6 GAS, CID:242, Fuel Injection, Aspiration:242, Engine VIN:, Desg:S
- 2000 Jeep Grand Cherokee Limited 4.7 V8 GAS, CID:287, Fuel Injection, Aspiration:287, Engine VIN:, Desg:N
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Jeep Grand Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Jeep Grand Cherokee cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2000 Jeep Grand Cherokee Laredo 4.0 L6 GAS
Front
- With vehicle in neutral, position vehicle on hoist.
- Remove half shaft hub/bearing nut.
- Remove wheel speed sensor nut from hub/bearing and remove sensor.
- Remove brake calipers bolts and remove calipers from caliper adapters.
- Remove lower stabilizer link bolt from control arm.
- Remove outer tie rod end nuts and separate tie rods from knuckles with remover tool ...
CLICK HERE TO GET FULL ACCESS TO 2000 Jeep Grand Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Jeep Grand Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Jeep Grand Cherokee cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace
Vehicle: 2000 Jeep Grand Cherokee Limited 4.7 V8 GAS
Clamp only the narrow forged portion of the yoke in the vise. Failure to heed caution may result in damage.
- Remove axle shaft.
- Remove bearing cap retaining snap rings. Saturate the bearing caps with penetrating oil prior to removal.
- Place socket (receiver) with inside diameter larger than bearing cap against yoke and perimeter of bearing cap to be removed.
- Pla...
CLICK HERE TO GET FULL ACCESS TO 2000 Jeep Grand Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Jeep Grand Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Jeep Grand Cherokee cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2000 Jeep Grand Cherokee Limited 4.7 V8 GAS
Front
- With vehicle in neutral, position vehicle on hoist.
- Mark a line across axle pinion flange, propeller shaft, flange yoke and transfer case for installation reference.
- Support transmission and transmission crossmember.
- Remove propeller shaft from transfer case flange.
- Remove propeller shaft from axle pinion flange.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Torque axle flange bolts to 80 ft. lbs.
- Torque transfer case flange bolts to 24 ft. lbs.
Rear
- With vehicle in neutral, positio...
CLICK HERE TO GET FULL ACCESS TO 2000 Jeep Grand Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Jeep Grand Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Jeep Grand Cherokee cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace
Vehicle: 2000 Jeep Grand Cherokee Laredo 4.0 L6 GAS
Clamp only the narrow forged portion of the yoke in the vise. Failure to heed caution may result in damage.
- Remove axle shaft.
- Remove bearing cap retaining snap rings. Saturate the bearing caps with penetrating oil prior to removal.
- Place socket (receiver) with inside diameter larger than bearing cap against yoke and perimeter of bearing cap to be removed.
- Pla...
CLICK HERE TO GET FULL ACCESS TO 2000 Jeep Grand Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Jeep Grand Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Jeep Grand Cherokee cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace
Vehicle: 2000 Jeep Grand Cherokee Laredo 4.7 V8 GAS
Clamp only the narrow forged portion of the yoke in the vise. Failure to heed caution may result in damage.
- Remove axle shaft.
- Remove bearing cap retaining snap rings. Saturate the bearing caps with penetrating oil prior to removal.
- Place socket (receiver) with inside diameter larger than bearing cap against yoke and perimeter of bearing cap to be removed.
- Pla...
CLICK HERE TO GET FULL ACCESS TO 2000 Jeep Grand Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Jeep Grand Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Jeep Grand Cherokee cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2000 Jeep Grand Cherokee Laredo 4.7 V8 GAS
Front
- With vehicle in neutral, position vehicle on hoist.
- Remove half shaft hub/bearing nut.
- Remove wheel speed sensor nut from hub/bearing and remove sensor.
- Remove brake calipers bolts and remove calipers from caliper adapters.
- Remove lower stabilizer link bolt from control arm.
- Remove outer tie rod end nuts and separate tie rods from knuckles with remover tool ...
CLICK HERE TO GET FULL ACCESS TO 2000 Jeep Grand Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
