Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2000 Subaru Outback car and truck
repair procedures including Subaru engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2000 Subaru Outback automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2000 Subaru Outback
- 2000 Subaru Outback 2.5 H4 GAS, CC:2458, Fuel Injection, Engine VIN:, Desg:6
- 2000 Subaru Outback 2.5 H4 GAS, CC:2458, Fuel Injection
- 2000 Subaru Outback Limited 2.5 H4 GAS, CC:2458, Fuel Injection, Engine VIN:, Desg:6
- 2000 Subaru Outback Limited 2.5 H4 GAS, CC:2458, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 2000 Subaru Outback AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Subaru Outback cars and light trucks from 1990+.
Anti-lock Brakes -> Legacy & Outback -> System Service -> ABS Control Module & Hydraulic Control Unit -> ABS Wheel Sensor -> Brake System Bleed -> Component Replacement -> Front -> Lateral G Sensor & Yaw Rate Sensor -> Rear -> Steering Angle Sensor
Vehicle: 2000 Subaru Outback 2.5 H4 GAS
Brake System Bleed
Two technicians are needed to bleed the brake system. Brake pedal operation must be very slow. Keep brake fluid reserve tank full to prevent air from entering the system during the bleeding procedure.
- Connect ABS check connector diagnosis terminal to terminal No. 6. Connector is located beside driver side seat heater unit.
- Start engine, then after ABS warning lamp goes out, depress brake pedal within 0.5 seconds.
- Check entire brake system for fluid leaks.
- Bleed air from right front caliper as follows:
- Fit one end of a vinyl tube onto air bleeder, place other end of t...
CLICK HERE TO GET FULL ACCESS TO 2000 Subaru Outback BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Subaru Outback AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Subaru Outback cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Master Cylinder
Vehicle: 2000 Subaru Outback Limited 2.5 H4 GAS
Master Cylinder
- Remove master cylinder from vehicle.
- Remove cylinder pin, Fig. .
- Push piston inward, then remove snap ring.
- Apply pressure to piston assembly while Inserting a small screwdriver into window of piston retainer and raise piston retainer latch, Fig. .
- Remove primary and secondary piston assemblies. Do not disassemble pistons. if disassembled, the spring settings will change.
- Inspect master cylinder inside diameter to piston clearance, Service limit is not to exceed 0.043 inch.
- Clean all parts with clean brake fluid, do...
CLICK HERE TO GET FULL ACCESS TO 2000 Subaru Outback BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Subaru Outback AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Subaru Outback cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 2000 Subaru Outback 2.5 H4 GAS
The brake booster is located inline between the master cylinder and the brake pedal. It serves to mechanically boost the force pushing the pistons of the master cylinder.
The brake booster consists of a power cylinder section and a power piston section. The power cylinder is made up of a front shell, rear shell and a diaphragm. The front and rear shells are connected with the diaphragm placed in between the two. The power cylinder chamber is closed to the atmosphere and the left and right chambers of the diaphragm are kept sealed.
The power piston is ...
CLICK HERE TO GET FULL ACCESS TO 2000 Subaru Outback BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Subaru Outback AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Subaru Outback cars and light trucks from 1990+.
Anti-lock Brakes -> Legacy & Outback -> Diagnosis & Testing -> ABS -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Component Testing -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation -> Less Select Monitor -> Preliminary Inspection -> VDC -> Wiring Diagrams -> With Select monitor
Vehicle: 2000 Subaru Outback 2.5 H4 GAS
Preliminary Inspection
- Ensure battery voltage is 12 volts or more and specific gravity is above 1.260.
- Inspect brake fluid level and for brake fluid leakage.
- Inspect brake drag.
- Inspect brake pads and rotors.
- Inspect tires for excessive wear and proper inflation.
Accessing Diagnostic Trouble Codes
Less Select Monitor
When on board diagnosis of the ABS/VDC control module detects a problem, the information (up to a maximum of three) will be stored in the EEPROM as a diagnostic trouble code (DTC). When there are more than three, the most recent three will be stored. Stored codes will s...
[[table data]] [[table data]] [[table data]] [[table data]]CLICK HERE TO GET FULL ACCESS TO 2000 Subaru Outback BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Subaru Outback AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Subaru Outback cars and light trucks from 1990+.
Anti-lock Brakes -> Legacy & Outback -> Description
Vehicle: 2000 Subaru Outback 2.5 H4 GAS
The Anti-lock Brake System (ABS) electrically controls brake fluid pressure to prevent wheel lock during braking on slippery road surfaces, which improves directional steering stability as well as shortening the braking distance.
If ABS becomes inoperative, the fail-safe system activates to ensure it acts as a conventional brake system. The warning light also comes on to indicate that the ABS is malfunctioning.
Vehicle Dynamics Control (VDC) system is a dri...
CLICK HERE TO GET FULL ACCESS TO 2000 Subaru Outback BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Subaru Outback AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Subaru Outback cars and light trucks from 1990+.
Power Brake Units -> Diagnosis & Testing
Vehicle: 2000 Subaru Outback 2.5 H4 GAS
Perform this procedure with the parking brakes applied.
- Start engine, then stop after one or two minutes of running time.
- Depress brake pedal several times with normal force.
- If pedal travel decreases the more times the brake pedal is depressed, the ...
CLICK HERE TO GET FULL ACCESS TO 2000 Subaru Outback BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2000 Subaru Outback vehicle.
|
| Access the Complete guide! |
