Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2000 Toyota Sienna car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2000 Toyota Sienna automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2000 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Toyota Sienna cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Except Land Cruiser & 4Runner -> Except Sienna -> Land Cruiser & 4Runner -> Master Cylinder -> Models w/Load Sensing Proportioning Valve (LSPV) -> Models w/Proportioning & Bypass Valve (P-BV) -> Proportioning Valve -> Sienna -> Wheel Cylinders
Vehicle: 2000 Toyota Sienna 3.0 V6 GAS
Master Cylinder
Except Sienna
- Remove brake fluid with syringe.
- On RAV4 models, remove air cleaner cover with air cleaner hose.
- On all models, label and disconnect brake lines using line wrench 09751-36011, 09023-00100, or equivalent. Cap brake lines from master cylinder.
- Disconnect wire connector from brake pressure switch and then disconnect level warning switch connector, if equipped.
- Remove master cylinder to brake unit attaching nuts, then remove master cylinder, wire clamp, gasket and 3-way union, as needed.
- Reverse procedure to install. Bleed brake system.
Sienna
- Remove air c...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Sienna BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Toyota Sienna cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> ABS Computer -> Brake Actuator -> Brake Lines -> Brake System Bleed -> Component Replacement -> Master Cylinder
Vehicle: 2000 Toyota Sienna 3.0 V6 GAS
Brake System Bleed
Master Cylinder
- Fill reservoir.
- Disconnect master cylinder tubes.
- Slowly depress brake pedal and hold.
- Block outlet holes with fingers and release pedal.
- Repeat 3-4 times.
Brake Lines
Bleed wheel with longest brake line first, then work your way back to the master cylinder according to brake line length.
- Connect brake cylinder tube.
- Depress pedal several times and hold.
- Loosen bleeder plug.
- When fluid stops coming out, tighten bleeder plug and release pedal.
- Repeat several times.
- Repeat entire procedure for each wheel.
- Fill reservoir.
Component Replacement
Brake Actuator
- Remove ...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Sienna BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Toyota Sienna cars and light trucks from 1990+.
Power Brake Units -> Troubleshooting
Vehicle: 2000 Toyota Sienna 3.0 V6 GAS
Refer to "Hydraulic Brake Systems" ...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Sienna BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Toyota Sienna cars and light trucks from 1990+.
Disc Brakes -> Front Disc Brakes -> Precautions -> Audio Coded Anti-Theft System
Vehicle: 2000 Toyota Sienna 3.0 V6 GAS
Audio Coded Anti-Theft System
Some models are equipped with an audio coded anti-theft system that will disable the radio when the battery cable is disconnected. The system can be identified by the "ANTI-THEFT SYSTEM" on the cassette tape lid. Obtain 3 digit customer code for input. Reset system after service as follows:
- Obtain 3 digit audio anti-theft code.
- Depress 1 (PROG) while depressing righthand side of TUNE SEEK button,- - - will appear in tape operation display.
- To enter the first digit, depress 1 (PROG) button repeatedly until the number of times depressed equals the first digit b...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Sienna BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Toyota Sienna cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> 2WD -> 4WD -> Camry & Camry Solara -> Celica & Corolla -> Echo & Tercel -> Inspection -> Installation -> Land Cruiser, Tundra & 4Runner -> RAV4 -> Removal -> Replacement -> Sienna -> Tacoma & T100
Vehicle: 2000 Toyota Sienna 3.0 V6 GAS
Camry & Camry Solara
Removal
- Raise and support rear of vehicle, then remove wheel and tire assembly.
- Remove brake drum. If brake drum cannot be remove easily, insert a suitable screwdriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
- Disconnect return spring, then remove front shoe hold-down spring, retainers and pin.
- Disconnect anchor spring, then remove front brake shoe and anchor spring, Fig. .
- Remove rear shoe hold-down spring, retainers and pin, using suitable tool, then disconnect parking brake cable from anchor plate.
- D...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Sienna BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Toyota Sienna cars and light trucks from 1990+.
Anti-lock Brakes -> Diagnosis & Testing -> 1997-2000 4RUNNER -> 1997-2000 RAV4 -> 1997-2001 CAMRY W/BOSCH ABS -> 1997-2001 CAMRY W/NIPPONDENSO ABS -> 1997-2001 CAMRY W/TRAC -> 1998-2000 SIENNA LESS VSC -> 2001-02 4RUNNER -> 2001-02 RAV4 -> 2001-02 SIENNA LESS VSC -> 2002 CAMRY W/ABS, BA, TRAC & VSC -> 2002 CAMRY W/BOSCH ABS -> 2002 CAMRY W/DENSO ABS -> 4Runner -> ABS Warning Lamp -> Accessing Diagnostic Trouble Codes -> Anti-Lock Brake System (ABS) -> Avalon -> AVALON LESS TRAC -> AVALON W/TRAC -> Avalon, Camry, Celica, Corolla, Echo, MR2, RAV4, Paseo, Sienna, Supra & Tercel -> Brake Actuator -> Camry -> Camry Solara -> CAMRY SOLARA LESS TRAC -> CAMRY SOLARA W/TRAC -> CELICA -> Clearing Diagnostic Trouble Codes -> Component Testing -> Corolla -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation -> Echo -> HIGHLANDER W/ABS, BA, TRAC & VSC -> HIGHLANDER W/BA & ABS -> Land Cruiser -> LAND CRUISER LESS VSC -> LAND CRUISER w/VSC -> Land Cruiser, Previa, Tacoma, T100 & 4Runner -> Less Toyota Hand Held Tester -> Less Toyota Hand-Held Tester -> MR2 -> PASEO -> Previa -> RAV4 -> Sequoia -> Sequoia & Tundra -> Sienna -> SIENNA W/VSC -> Speed Sensor -> Stop Lamp Switch -> Supra -> SUPRA LESS TRAC -> SUPRA W/TRAC -> System Testing -> T100 -> Tacoma -> Tc Terminal -> Tercel -> Traction Control (TRAC) Warning Lamp -> Ts Terminal -> Tundra -> Vehicle Skid Control (VSC) Warning Lamp -> Wiring Diagrams -> With Toyota Hand Held Tester -> With Toyota Hand-Held Tester
Vehicle: 2000 Toyota Sienna 3.0 V6 GAS
Accessing Diagnostic Trouble Codes
Less Toyota Hand-Held Tester
- On Land Cruiser models, ensure center differential is free.
- On all models, turn ignition switch to On position.
- Disconnect short pin from Data Link Connector 1 (DLC1).
- Connect terminals Tc and E1 or CG of DLC1 or DLC3 using tool No. 09843-18020, or equivalent, Figs. through .
- Read and record number of times ANTI-LOCK warning lamp flashes.
- If system is operating properly, (no faults) warning lamp will blink once every .25 seconds.
- Connect actuator check connector and ensure proper operation.
With Toyota Hand-Held Tester
- O...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Sienna BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2000 Toyota Sienna vehicle.
|
| Access the Complete guide! |
