Auto Parts Search
2001 Ford Mustang CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 2001 Ford Mustang AUTOMOBILES
Component Replacement & Adjustment -> Passenger Cars -> Evaporator Core, Replace -> Continental -> Cougar -> Crown Victoria & Grand Marquis -> Escort -> Focus -> LS & Thunderbird -> Mustang -> Sable & Taurus -> Town Car
Vehicle: 2001 Ford Mustang Bullitt 4.6 V8 GAS
Continental
The evaporator core is not serviced separately and can only be replaced with the evaporator housing assembly.
- Remove seats and rear seat airflow duct.
- Remove instrument panel as outlined under "Instrument Panel."
- Drain coolant into suitable container to level below heater core.
- Recover refrigerant as outlined under .
- Disconnect Powertrain Control Module (PCM) electrical connector.
- Disconnect heater core hoses.
- Disconnect vacuum supply hose.
- Disconnect condenser to evaporator tube and evaporato...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Ford Mustang AUTOMOBILES
Hydraulic Brake Systems -> Component Service -> Assemble -> Disassemble -> Inspection -> Master Cylinder Overhaul -> Overhaul -> Wheel Cylinders
Vehicle: 2001 Ford Mustang Bullitt 4.6 V8 GAS
Master Cylinder Overhaul
Disassemble
- Clean outside of master cylinder thoroughly. Drain brake fluid from master cylinder.
- Remove stop bolt and pressure control valves, if equipped.
- Pry up on reservoir and remove it from master cylinder body.
- Remove fluid control valve, if equipped.
- Depress primary piston and remove snap ring from retaining groove at open end of bore.
- Remove primary and secondary piston assemblies from master cylinder. If secondary piston does not come out, apply air pressure to secondary outlet port to remove.
Inspection
When disassembled, wash all parts in clean brake...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 2001 Ford Mustang AUTOMOBILES
Ford Motor Co. Passenger Cars -> Fuel Pressure Relief -> Except Aspire, Festiva, Focus, Fusion, Milan, 2003-06 Crown Victoria, Grand Marquis, Sable, Taurus & Town Car, 1991-96 Escort, 1988-96 Tracer, 1991-94 Capri, 1989-91 Probe & 2005-06 Mustang
Vehicle: 2001 Ford Mustang Bullitt 4.6 V8 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
When installing the fuel filter, ensure the flow arrow is facing in the proper direction...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 Ford Mustang AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2001 Ford Mustang Cobra 4.6 V8 GAS
- Raise and support vehicle.
- Remove exhaust hangers from rubber mounts.
- Remove two mounting nuts on lefthand side exhaust flange.
- Lower the muffler pipe to clear flange, then move muffler forward to disconnect third exhaust hanger.
- Mark driveshaft companion flange to pinion flange for installation align...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2001 Ford Mustang AUTOMOBILES
Starter, Replace
Vehicle: 2001 Ford Mustang 3.8 V6 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- Remove ground cable nut.
- Remove solenoid protective cap and wiring nuts. Position wiring aside.
- Remove starter motor mounting bolts, then starter motor from vehicle...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2001 Ford Mustang AUTOMOBILES
Ford Motor Co. Cars -> Check Engine Lamp/Malfunction Indicator Lamp (MIL)/Service Engine Soon Lamp -> 1998-2006 Models -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool
Vehicle: 2001 Ford Mustang Cobra 4.6 V8 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-V system. If the lamp remains On or starts to blink, a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
A temporary fault such as running out of fuel, poor quality or water in fuel or loos...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2001 Ford Mustang AUTOMOBILES
Heater Hose, Replace -> Bypass -> Inlet -> Outlet
Vehicle: 2001 Ford Mustang 3.8 V6 GAS
Inlet
- Drain cooling system into a suitable container.
- Remove intake manifold.
- Reposition heater hose inlet clamp at heater core.
- Remove heater inlet hose from heater core.
- Reposition heater core inlet hose clamp at engine.
- Remove hose from engine.
- Remove hose from vehicle.
- Reverse procedure to install.
Outlet
- Drain cooling system into a suitable container.
- Remove intake manifold.
- Reposition heater hose outlet clamp at heater core.
- Disconnect heater...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2001 Ford Mustang AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2001 Ford Mustang Bullitt 4.6 V8 GAS
- Insert a suitable square drive tool into square hole in tensioner arm, then rotate tensioner...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2001 Ford Mustang AUTOMOBILES
Component location diagrams for most 2001 Ford Mustang cars and light trucks sold in the U.S. from 1990+.
Cowl Component Locations Diagram for 2001 Ford Mustang GT 4.6 V8 GAS Components on diagram: |
Body Component Locations Diagram for 2001 Ford Mustang GT 4.6 V8 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2001 Ford Mustang AUTOMOBILES
OEM drawn wiring diagrams for most 2001 Ford Mustang cars and light trucks sold in the U.S.
2001 Ford Mustang Cobra 4.6 V8 GAS Wiring Diagram Components on diagram: |
2001 Ford Mustang Bullitt 4.6 V8 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2001 Ford Mustang AUTOMOBILES
OEM TSB listings for most 2001 Ford Mustang cars and light trucks sold in the U.S. from 1985+.
Document: RECALL - CERTAIN 1992-2003 MODEL YEAR CARS AND TRUCKS - FUSED JUMPER HARNESS REPLACEMENT FOR VEHICLES SERVICED WITH AN INCOMPATIBLE FUSED JUMPER HARNESS Vehicle: 2001 Ford Mustang 3.8 V6 GAS Auto Systems: |
Document: RECALL - 1992-2004 MULTIPLE VEHICLE LINES - SPEED CONTROL SYSTEM MODIFICATION Vehicle: 2001 Ford Mustang 3.8 V6 GAS |
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2001 Ford Mustang AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2001 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2001 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2001 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2001 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Mustang SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2001 Ford Mustang vehicle. |
Access the Complete guide! |