Auto Parts Search
We have info for following modifications of 2001 GMC Yukon
- 2001 GMC Yukon 4.8 V8 GAS, CID:294, Fuel Injection, Aspiration:294, Engine VIN:, Desg:V
- 2001 GMC Yukon 5.3 V8 GAS, CID:323, Fuel Injection, Aspiration:323, Engine VIN:, Desg:T
- 2001 GMC Yukon Denali 6.0 V8 GAS, CID:364, Fuel Injection, Aspiration:364, Engine VIN:, Desg:U
- 2001 GMC Yukon Denali XL 6.0 V8 GAS, CID:364, Fuel Injection, Aspiration:364, Engine VIN:, Desg:U
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 GMC Yukon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 GMC Yukon cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Front, All Except NP8 Axle -> Front, NP8 Axle -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2001 GMC Yukon 4.8 V8 GAS
Front
Front, All Except NP8 Axle
- Raise and support vehicle.
- Remove front differential carrier shield, if used.
- Reference mark relationship of propeller shaft to front axle and transfer case flange.
- Remove bolts and retainers from front axle.
- Remove bolts and retainers from transfer case.
- Remove propeller shaft. When removing propeller shaft, do not attempt to remove shaft by pounding on yoke ears or using a tool between yoke and universal joint. If propeller shaft is removed by using such means, injection joints may fracture and lead to premature failure of joint.
- Compress propeller...
CLICK HERE TO GET FULL ACCESS TO 2001 GMC Yukon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 GMC Yukon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 GMC Yukon cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2001 GMC Yukon Denali XL 6.0 V8 GAS
Front
Before disassembly, observe and accurately reference mark all driveline components relative to the propeller shaft and axles. These items include propeller shafts, wheel drive shafts, pinion flanges, and output shafts.
Assemble all components in the exact relationship to each other as they were prior to removal. Observe all published specifications and torque values, and any measurements obtained prior to disassembly.
- Raise and support vehicle.
- Remove transfer case shield, if equipped.
- If equipped with double clamp style boot, remove clamp at transfer case by prying up expo...
CLICK HERE TO GET FULL ACCESS TO 2001 GMC Yukon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 GMC Yukon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 GMC Yukon cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2001 GMC Yukon 5.3 V8 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 2001 GMC Yukon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 GMC Yukon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 GMC Yukon cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2001 GMC Yukon 4.8 V8 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 2001 GMC Yukon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 GMC Yukon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 GMC Yukon cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Front, All Except NP8 Axle -> Front, NP8 Axle -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2001 GMC Yukon Denali 6.0 V8 GAS
Front
Front, All Except NP8 Axle
- Raise and support vehicle.
- Remove front differential carrier shield, if used.
- Reference mark relationship of propeller shaft to front axle and transfer case flange.
- Remove bolts and retainers from front axle.
- Remove bolts and retainers from transfer case.
- Remove propeller shaft. When removing propeller shaft, do not attempt to remove shaft by pounding on yoke ears or using a tool between yoke and universal joint. If propeller shaft is removed by using such means, injection joints may fracture and lead to premature failure of joint.
- Compress propeller...
CLICK HERE TO GET FULL ACCESS TO 2001 GMC Yukon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 GMC Yukon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 GMC Yukon cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2001 GMC Yukon Denali 6.0 V8 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 2001 GMC Yukon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2001 GMC Yukon vehicle. |
Access the Complete guide! |