Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2001 KIA RIO car and truck
repair procedures including KIA engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2001 KIA RIO automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2001 KIA RIO AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 KIA RIO cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Master Cylinder -> Rio -> Sedona -> Sephia & Spectra -> Sportage
Vehicle: 2001 KIA RIO 1.5 L4 GAS
Hydraulic brake fluid will damage painted surfaces. If fluid gets on painted surface, wipe clean immediately.
Master Cylinder
Rio
- Remove master cylinder in numbered sequence, Fig. , noting the following:
- Disconnect brake lines from master cylinder and ABS control unit using flare nut wrench tool No. OK130 430 019, or equivalent.
- Plug all open lines and ports to prevent entry of dirt or debris.
- Reverse procedure to install, noting the following:
- Place adjustment gauge tool No. OK370 430 018, or equivalent, onto master cylinder, Fig. .
- Apply 19.7 inches of vacuum to booster unit usi...
CLICK HERE TO GET FULL ACCESS TO 2001 KIA RIO BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 KIA RIO AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 KIA RIO cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> Front -> Inspection -> Rear -> Replacement -> Rio -> Rio & Sephia -> Sedona -> Sephia & Spectra -> Sportage
Vehicle: 2001 KIA RIO 1.5 L4 GAS
Replacement
Front
Rio
- Remove front disc brakes in numbered sequence as required, Fig. .
- Reverse procedure to install. Tighten bolts and wheel lug nuts to specifications.
Sedona
- Raise and support vehicle.
- Remove tire and wheel.
- Remove caliper mounting bolts, then position caliper aside using suitable wire or rope.
- Remove pads from caliper.
- Reverse procedure to install, noting the following:
- Use brake expander tool No. 0K130 430 017, or equivalent, when inserting new pads.
- Bleed brake system as outlined in "Hydraulic Brake Systems."
Sephia & Spectra
- Remove front disc brakes in numbered sequenc...
CLICK HERE TO GET FULL ACCESS TO 2001 KIA RIO BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 KIA RIO AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 KIA RIO cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Replacement
Vehicle: 2001 KIA RIO 1.5 L4 GAS
Replacement
- Remove master cylinder as outlined in "Hydraulic Brake Systems."
- Remove power brake unit in numbered sequence, Fig. .
- Reverse procedure to install, noting the following:
- Inspect all...
CLICK HERE TO GET FULL ACCESS TO 2001 KIA RIO BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 KIA RIO AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 KIA RIO cars and light trucks from 1990+.
Anti-lock Brakes -> Rio -> System Service -> Brake System Bleed -> Component Replacement -> Front Wheel Speed Sensor -> Hydraulic Control Unit (HCU) -> Rear Wheel Speed Sensor
Vehicle: 2001 KIA RIO 1.5 L4 GAS
Brake System Bleed
Refer to "Hydraulic Brake Systems" for brake bleeding procedure.
Component Replacement
Hydraulic Control Unit (HCU)
- Disconnect HCU electrical connectors.
- Disconnect brake line fittings at HCU using a suitable flare nut wrench.
- Plug all open lines and ports to prevent entry of dirt or debris.
- Remove HCU mounting bracket bolt and nut, then the HCU.
- Reverse procedure to install, noting the following:
- Torque HCU mounting bracket bolt and nut to 12-20 ft. lbs.
- Torque brake line fittings to 10-16 ft. lbs.
- Bleed brakes as outlined under "Brake System Bleed."
Front Wheel Speed Sensor
- R...
CLICK HERE TO GET FULL ACCESS TO 2001 KIA RIO BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 KIA RIO AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 KIA RIO cars and light trucks from 1990+.
Disc Brakes -> Brake System Bleed
Vehicle: 2001 KIA RIO 1.5 L4 GAS
- Ensure brake fluid reservoir remains at least 3/4 full during entire bleed procedure.
- Raise and support vehicle.
- Remove bleeder cap at bleeder screw farthest from master cylinder and attach a vinyl hose to bleeder screw.
- Place other end of tube in a clear container filled with fresh brake flui...
CLICK HERE TO GET FULL ACCESS TO 2001 KIA RIO BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 KIA RIO AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 KIA RIO cars and light trucks from 1990+.
Disc Brakes -> Rotor Replacement
Vehicle: 2001 KIA RIO 1.5 L4 GAS
Replace rotor as...
CLICK HERE TO GET FULL ACCESS TO 2001 KIA RIO BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
