Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2001 Subaru Impreza car and truck
repair procedures including Subaru engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2001 Subaru Impreza automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2001 Subaru Impreza
- 2001 Subaru Impreza 2.2 H4 GAS, CC:2212, Fuel Injection, Engine VIN:, Desg:4
- 2001 Subaru Impreza Outback 2.2 H4 GAS, CC:2212, Fuel Injection, Engine VIN:, Desg:4
- 2001 Subaru Impreza RS 2.5 H4 GAS, CC:2458, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 2001 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Subaru Impreza cars and light trucks from 1990+.
Anti-lock Brakes -> Impreza -> System Service -> ABS Control Module & Hydraulic Control Unit -> ABS Wheel Sensor -> Brake System Bleed -> Component Replacement -> Front -> G Sensor -> Rear
Vehicle: 2001 Subaru Impreza RS 2.5 H4 GAS
Brake System Bleed
- Start with wheels connecting to secondary chamber of master cylinder.
- Inspect for leaks at joints and connection in brake system, repair as necessary.
- Fit one end of a suitable vinyl hose over brake bleeder and place other end into a container filled with brake fluid.
- Slowly depress brake pedal and keep depressed.
- Open bleeder crew and release fluid for one to two seconds.
- Close bleeder screw and release pedal.
- Repeat steps until all air is discharged from system.
Component Replacement
ABS Wheel Sensor
Front
- Disconnect ABS sensor connector located in engine compartment ne...
CLICK HERE TO GET FULL ACCESS TO 2001 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Subaru Impreza cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Brake Booster, Replace -> Forester, Impreza, Legacy & Outback -> Overhaul -> SVX
Vehicle: 2001 Subaru Impreza RS 2.5 H4 GAS
Brake Booster, Replace
Forester, Impreza, Legacy & Outback
- Disconnect brake fluid level indicator connector, if equipped.
- Remove master cylinder assembly.
- Disconnect vacuum hose from brake booster.
- Working from inside the passenger compartment, remove snap pin and operating rod clevis pin from brake pedal assembly.
- Remove brake booster retaining nuts, then brake booster from vehicle.
- Reverse procedure to install. Torque brake booster retaining nuts to 10-17 ft. lbs.
SVX
- Raise and support vehicle and remo...
CLICK HERE TO GET FULL ACCESS TO 2001 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Subaru Impreza cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> Front -> Rear
Vehicle: 2001 Subaru Impreza Outback 2.2 H4 GAS
Front
- Raise and support vehicle.
- Remove front wheels.
- Disconnect brake hose from strut.
- Remove caliper lockpin, then rotate caliper on guide pin, Figs. through .
- Remove brake pads from support.
- Reverse procedure to install noting the following:
- Push piston into caliper body. When piston is difficult to insert, loosen the air bleeder, then push into place.
- Refer to Figs. and for tightening values.
- After completing installation, depress brake pedal several times to seat brake pads against rotor. If pedal stroke is excessive, bleed hydraulic system as outlined under, "Hydraulic Brake S... "
CLICK HERE TO GET FULL ACCESS TO 2001 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Subaru Impreza cars and light trucks from 1990+.
Drum Brakes -> Adjustments -> Drum Brake -> Forester & Impreza -> Legacy, Outback & SVX -> Parking Brake
Vehicle: 2001 Subaru Impreza RS 2.5 H4 GAS
Parking Brake
Legacy, Outback & SVX
- Pull parking brake lever three to five times. Mechanism should click six to seven times when a force of 55 lbs. is exerted on the lever.
- If lever operation is not as specified, adjust lever stroke by turning adjuster nut, Fig. .
- After adjustment procedure is complete, tighten adjuster locknut to specification.
Forester & Impreza
- Pull parking brake lever with a force of...
CLICK HERE TO GET FULL ACCESS TO 2001 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Subaru Impreza cars and light trucks from 1990+.
Anti-lock Brakes -> Impreza -> System Service -> ABS Control Module & Hydraulic Control Unit -> ABS Wheel Sensor -> Brake System Bleed -> Component Replacement -> Front -> G Sensor -> Rear
Vehicle: 2001 Subaru Impreza 2.2 H4 GAS
Brake System Bleed
- Start with wheels connecting to secondary chamber of master cylinder.
- Inspect for leaks at joints and connection in brake system, repair as necessary.
- Fit one end of a suitable vinyl hose over brake bleeder and place other end into a container filled with brake fluid.
- Slowly depress brake pedal and keep depressed.
- Open bleeder crew and release fluid for one to two seconds.
- Close bleeder screw and release pedal.
- Repeat steps until all air is discharged from system.
Component Replacement
ABS Wheel Sensor
Front
- Disconnect ABS sensor connector located in engine compartment ne...
CLICK HERE TO GET FULL ACCESS TO 2001 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Subaru Impreza cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Dual Proportioning Valve -> Master Cylinder
Vehicle: 2001 Subaru Impreza RS 2.5 H4 GAS
Master Cylinder
- Disconnect brake lines from master cylinder and plug the ends.
- If applicable, disconnect fluid warning switch electrical connector.
- Remove master cylinder retaining nuts and the master cylinder.
- Reverse procedure to install.
- Bleed hydraulic system after completing installation.
Dual Proportioning Valve
Inspect brake line connections at DPV f...
CLICK HERE TO GET FULL ACCESS TO 2001 Subaru Impreza BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2001 Subaru Impreza vehicle.
|
| Access the Complete guide! |
