Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2002 Infiniti I35 car and truck
repair procedures including Infiniti engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2002 Infiniti I35 automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2002 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Infiniti I35 cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> 1999 -> 2000-02 -> Actuator -> Actuator Relays -> Brake System Bleed -> Component Replacement -> Front -> G20 -> G20, I30 & I35 -> I30 & I35 -> I35 -> J30 -> J30 & Q45 -> Q45 -> Rear -> Speed Sensors -> Speed Sensors Rotor -> VDC/TCS/ABS Control Module -> Yaw Rate/G Sensor
Vehicle: 2002 Infiniti I35 3.5 V6 GAS
Brake System Bleed
Refer to "Hydraulic Brake System" for procedure.
Component Replacement
Speed Sensors
- Disconnect wiring connector.
- Remove mounting bolt and sensor, Figs. through .
- Reverse procedure to install, noting the following:
- On G20 and I30 models, torque front wheel sensor mounting bolts to 13-17 ft. lbs.
- On G20 and I30 models, torque rear wheel sensor mounting bolts to 18-25 ft. lbs.
- On J30 & Q45 models, torque wheel sensor mounting bolts to 96-132 inch lbs.
Speed Sensors Rotor
G20, I30 & I35
Front
- Remove drive shaft as outlined in "Front Wheel Drive Axles."
- Remove sensor rotor using su...
CLICK HERE TO GET FULL ACCESS TO 2002 Infiniti I35 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Infiniti I35 cars and light trucks from 1990+.
Anti-lock Brakes -> Troubleshooting -> Procedure Interpretation Chart
Vehicle: 2002 Infiniti I35 3.5 V6 GAS
Refer to Figs. through for troublesh...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2002 Infiniti I35 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Infiniti I35 cars and light trucks from 1990+.
Disc Brakes -> Adjustments -> 1997-2001 -> 2002 -> Brake Pedal -> G20 -> I30 & I35 -> J30 -> J30 & Q45 -> Parking Brake -> Q45
Vehicle: 2002 Infiniti I35 3.5 V6 GAS
Brake Pedal
G20
Refer to Fig. when adjusting brake pedal, noting the following"
- On models equipped with automatic transaxle, brake pedal height should be 6.26-6.65 inches.
- On models equipped with manual transaxle, brake pedal height should be 5.94-6.34 inches.
- On all models, pedal stopper to stop lamp or speed control switch should be .012-.039 inch.
I30 & I35
- Inspect brake pedal free height from dash reinforcement panel, Fig. .
- Loosen lock nut and adjust pedal free height by turning brake booster input rod. Tighten lock nut, Fig. .
- Inspect pedal free play and ensure stop lamps go off when ...
CLICK HERE TO GET FULL ACCESS TO 2002 Infiniti I35 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Infiniti I35 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 2002 Infiniti I35 3.5 V6 GAS
Do not spill brake fluid on painted surfaces, it may cause damage to the paint. If brake fluid is spilled, wash immediately with water.
- Place container under master cylinder to avoid spillage, then fill master cylinder with brake fluid.
- Connect hose to bleeder valves and depress brake pedal several times.
- With pressure applied to pedal...
CLICK HERE TO GET FULL ACCESS TO 2002 Infiniti I35 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Infiniti I35 cars and light trucks from 1990+.
Disc Brakes -> Parking Brake Service -> G20, I30 & I35 -> Inspection -> J30 & Q45 -> Replace
Vehicle: 2002 Infiniti I35 3.5 V6 GAS
Replace
G20, I30 & I35
Refer to Figs. and when inspecting and removing the parking brake cable.
- Remove center console.
- Disconnect warning switch connector, Fig. .
- Remove mounting bolts and adjusting nut.
- Remove parking brake cable lock plate, Fig. .
J30 & Q45
- Raise and support vehicle, then remove wheels.
- Remove caliper mounting pins/bolts without disconnecting brake hose, Fig. .
- If removing rear rotors, remove adjuster hole plug, then back off...
CLICK HERE TO GET FULL ACCESS TO 2002 Infiniti I35 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Infiniti I35 cars and light trucks from 1990+.
Anti-lock Brakes -> Precautions -> Battery Ground Cable
Vehicle: 2002 Infiniti I35 3.5 V6 GAS
Battery Ground Cable
Prior to servic...
CLICK HERE TO GET FULL ACCESS TO 2002 Infiniti I35 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
