Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2002 Jaguar S-TYPE car and truck
repair procedures including Jaguar engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2002 Jaguar S-TYPE automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2002 Jaguar S-TYPE
- 2002 Jaguar S-TYPE 3.0 V6 GAS, CID:183, Fuel Injection, Aspiration:183, Engine VIN:, Desg:F
- 2002 Jaguar S-TYPE 4.0 V8 GAS, CC:3996, CID:244, Fuel Injection, Aspiration:244, Engine VIN:, Desg:G
BRAKE SERVICE PROCEDURES FOR 2002 Jaguar S-TYPE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Jaguar S-TYPE cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> ABS/Traction Control Module (ABS/TCM) -> Brake System Bleed -> Component Replacement -> Fluid Intake Hose -> Front -> Hydraulic Control Unit (HCU) -> Lateral Acceleration & Rotation Sensors -> Rear -> S-Type -> Steering Wheel Rotation Sensor -> Wheel Speed Sensor -> X-Type -> XKR & XK8 -> Yaw Rate Sensor
Vehicle: 2002 Jaguar S-TYPE 3.0 V6 GAS
Brake System Bleed
Bleeding the ABS system is not a routine maintenance operation and is only required when part of the system has been disconnected or the fluid is contaminated.
During the bleeding procedure, it is important that the level of fluid in the reservoir is maintained at approximately .0787 inch below the bottom of the filler neck. Motor/pump unit cannot charge accumulator if air and not fluid, is standing on low pressure side of pump.
If motor/pump unit, fluid intake hose or hydraulic unit of ABS system has been removed or disconnected, bleed as outlined in "Fluid Intake... "
CLICK HERE TO GET FULL ACCESS TO 2002 Jaguar S-TYPE BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Jaguar S-TYPE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Jaguar S-TYPE cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Front, Replace -> Rear, Replace -> S-Type & X-Type -> XKR & XK8
Vehicle: 2002 Jaguar S-TYPE 4.0 V8 GAS
Front, Replace
S-Type & X-Type
- Raise and support vehicle, then remove tire and wheel assembly.
- Apply suitable brake pedal hold down tool and adjust pedal down approximately 1.6 inches.
- Install suitable bleeder bottle on nipple and loosen, then remove brake pipe from caliper.
- Remove guide pin mounting bolt and caliper.
- Reverse procedure to install. Bleed brake system as outlined under, "Hydraulic Brake Systems."
XKR & XK8
- Raise and support vehicle, then remove tire and wheel assembly.
- Remove caliper retaining spring and feed hose.
- Plug feed hose and caliper.
- Remove caps, guide pins and calipe...
CLICK HERE TO GET FULL ACCESS TO 2002 Jaguar S-TYPE BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Jaguar S-TYPE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Jaguar S-TYPE cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Master Cylinder
Vehicle: 2002 Jaguar S-TYPE 4.0 V8 GAS
Master Cylinder
- Remove master cylinder as outlined in this section.
- Carefully pry out master cylinder hydraulic line adapters from sealing grommets.
- Remove sealing grommets from master cylinder by levering out using suitable screwdriver.
- Press primary piston stop pin in to relieve secondary piston stop pin pressure.
- Remove front grommet sealing housing stop pin. Maintain pressure on primary piston and remove cir-clip.
- Remove primary/secondary pistons and spring assemblies by tapping master cylinder open flanged end on suitable wooden block. Compressed air may have to be applied to m...
CLICK HERE TO GET FULL ACCESS TO 2002 Jaguar S-TYPE BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Jaguar S-TYPE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Jaguar S-TYPE cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Replacement -> S-Type & X-Type -> XKR & XK8
Vehicle: 2002 Jaguar S-TYPE 3.0 V6 GAS
Replacement
S-Type & X-Type
- Remove wiper arms.
- Remove cowl grille and engine compartment brace.
- Remove master cylinder as outlined in "Hydraulic Brake Systems" section.
- Remove expansion tank.
- Remove mounting screws and disconnect clips, then remove driver's side instrument panel lower panel.
- Disconnect fuel flap and luggage compartment release switch electrical connector.
- Remove mounting screws and driver's side air duct.
- Disconnect hood latch release handle supporting plate.
- Remove clip and brake booster retaining pin.
- Remove mounting nuts and brake booster with non-return valve/va...
CLICK HERE TO GET FULL ACCESS TO 2002 Jaguar S-TYPE BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Jaguar S-TYPE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Jaguar S-TYPE cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Master Cylinder
Vehicle: 2002 Jaguar S-TYPE 3.0 V6 GAS
Master Cylinder
- Remove master cylinder as outlined in this section.
- Carefully pry out master cylinder hydraulic line adapters from sealing grommets.
- Remove sealing grommets from master cylinder by levering out using suitable screwdriver.
- Press primary piston stop pin in to relieve secondary piston stop pin pressure.
- Remove front grommet sealing housing stop pin. Maintain pressure on primary piston and remove cir-clip.
- Remove primary/secondary pistons and spring assemblies by tapping master cylinder open flanged end on suitable wooden block. Compressed air may have to be applied to m...
CLICK HERE TO GET FULL ACCESS TO 2002 Jaguar S-TYPE BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Jaguar S-TYPE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Jaguar S-TYPE cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Front, Replace -> Rear, Replace -> S-Type & X-Type -> XKR & XK8
Vehicle: 2002 Jaguar S-TYPE 3.0 V6 GAS
Front, Replace
S-Type & X-Type
- Raise and support vehicle, then remove tire and wheel assembly.
- Apply suitable brake pedal hold down tool and adjust pedal down approximately 1.6 inches.
- Install suitable bleeder bottle on nipple and loosen, then remove brake pipe from caliper.
- Remove guide pin mounting bolt and caliper.
- Reverse procedure to install. Bleed brake system as outlined under, "Hydraulic Brake Systems."
XKR & XK8
- Raise and support vehicle, then remove tire and wheel assembly.
- Remove caliper retaining spring and feed hose.
- Plug feed hose and caliper.
- Remove caps, guide pins and calipe...
CLICK HERE TO GET FULL ACCESS TO 2002 Jaguar S-TYPE BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2002 Jaguar S-TYPE vehicle.
|
| Access the Complete guide! |
