Auto Parts Search
We have info for following modifications of 2003 Chevrolet Tracker
- 2003 Chevrolet Tracker 2.0 L4 GAS, CID:122, Fuel Injection, Aspiration:122, Engine VIN:, Desg:C
- 2003 Chevrolet Tracker 2.5 V6 GAS, CC:2500, Fuel Injection, Engine VIN:, Desg:4
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Chevrolet Tracker AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Chevrolet Tracker cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Left -> Right
Vehicle: 2003 Chevrolet Tracker 2.5 V6 GAS
Left
- Raise and support vehicle.
- Remove skid plate bolts and skid plate, if equipped.
- Remove front tire and wheel assembly.
- Remove the six hub flange bolts and flange.
- Remove drive axle shaft snap ring.
- Remove drive axle shaft spindle washer from drive axle shaft.
- Use a hydraulic jack in order to support the front control arm. To prevent personal injury and/or component damage, use the proper tools to support the lower control arm when removing the coil spring. The coil spring is under extreme pressure and can become a projectile should the spring separate from the lower control ...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Tracker DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Chevrolet Tracker AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Chevrolet Tracker cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2003 Chevrolet Tracker 2.5 V6 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Tracker DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Chevrolet Tracker AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Chevrolet Tracker cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Two Piece Driveshaft
Vehicle: 2003 Chevrolet Tracker 2.0 L4 GAS
Front
- Raise and support vehicle.
- If vehicle is equipped with a transfer case,place drain pan or suitable container underneath transfer case. Remove drain plug and drain fluid.
- Place index marks on pinion flange yoke and differential pinion flange.
- Remove bolts and nuts holding yoke, then separate pinion flange yoke from differential pinion flange.
- Remove sliding yoke from transfer case, then remove propeller shaft from vehicle.
- Inspect propeller shaft for dents or other damage. Replace shaft if damaged.
- Inspect universal joints for smooth pivoting. If universal joints bind or appea...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Tracker DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Chevrolet Tracker AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Chevrolet Tracker cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Left -> Right
Vehicle: 2003 Chevrolet Tracker 2.0 L4 GAS
Left
- Raise and support vehicle.
- Remove skid plate bolts and skid plate, if equipped.
- Remove front tire and wheel assembly.
- Remove the six hub flange bolts and flange.
- Remove drive axle shaft snap ring.
- Remove drive axle shaft spindle washer from drive axle shaft.
- Use a hydraulic jack in order to support the front control arm. To prevent personal injury and/or component damage, use the proper tools to support the lower control arm when removing the coil spring. The coil spring is under extreme pressure and can become a projectile should the spring separate from the lower control ...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Tracker DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Chevrolet Tracker AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Chevrolet Tracker cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2003 Chevrolet Tracker 2.0 L4 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Tracker DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Chevrolet Tracker AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Chevrolet Tracker cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Two Piece Driveshaft
Vehicle: 2003 Chevrolet Tracker 2.5 V6 GAS
Front
- Raise and support vehicle.
- If vehicle is equipped with a transfer case,place drain pan or suitable container underneath transfer case. Remove drain plug and drain fluid.
- Place index marks on pinion flange yoke and differential pinion flange.
- Remove bolts and nuts holding yoke, then separate pinion flange yoke from differential pinion flange.
- Remove sliding yoke from transfer case, then remove propeller shaft from vehicle.
- Inspect propeller shaft for dents or other damage. Replace shaft if damaged.
- Inspect universal joints for smooth pivoting. If universal joints bind or appea...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Tracker DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2003 Chevrolet Tracker vehicle. |
Access the Complete guide! |