Auto Parts Search
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Low Coolant Lamp ->
Vehicle: 2003 Ford Windstar 3.8 V6 GAS
This lamp should light when engine coolant level in the radiator drops below a predetermined le...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Fuel Cap Lamp ->
Vehicle: 2003 Ford Windstar 3.8 V6 GAS
The Check Fuel Cap Lamp will illuminate momentarily when the ignition switch is placed in the On position as a bulb check. If the lamp remains...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Emission Maintenance Reminder Indicator ->
Vehicle: 2003 Ford Windstar 3.8 V6 GAS
This lamp should light after approximately 60,000 miles of operation, Fig. . The amber lens lamp is located on the instrument panel and has the word Emissions, Emiss or EGR printed on it. After performing the required emission control maintenance, the module must be replaced or reset, depending on type of module used. On module equipped with reset feature, reset the module as follows:
- Turn ignition Off.
- On Aerostar models, the module is located under the instrument panel near the bulkhead connector.
- On Bronco, Explorer and F-Series, the module is attached to the instrument cluster to the left of ...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Anti-Lock Or Rear Anti-Lock Brake System Warning ->
Vehicle: 2003 Ford Windstar 3.8 V6 GAS
Red and yellow indicator lamps are used to warn of system faults. The red lamp warns of such faults as low brake fluid level, parking brake On, system pressure differential and other system faults. The red indicator lamp will light for approximately two seconds during engine starting and should go off, unless parking brake is applied or a problem in the brake system exist. The red indicator lamp should reset after repairs to system have ...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Low Oil Level Warning Indicator ->
Vehicle: 2003 Ford Windstar 3.8 V6 GAS
This system is used to indicate a low engine oil level condition. The lamp should light during engine starting. If oil level is sufficient, the lamp should go off when engine is operating. If oil level is low the...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Message Center -> 1999-2003 Windstar -> System Check
Vehicle: 2003 Ford Windstar 3.8 V6 GAS
System Check
The Message Center will perform a system inspection of monitored systems and will indicate either system is OK or a warning message. To perform the System Check proceed as follows:
- Place the ignition switch in the On position.
- Press Message Center Set Up button.
- From Set Up Menu select System Check.
- Press the RESET button to start system inspection.
- The Message Center will cycle through the monitored systems and display an OK or Warning Message for 4 seconds.
- Depressing the RESET button will cycle the Message Center through of the monitored systems.
- Pressing the RESET bu...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2003 Ford Windstar vehicle. |
Access the Complete guide! |