Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2003 Volvo XC90 car and truck
repair procedures including Volvo engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2003 Volvo XC90 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2003 Volvo XC90
- 2003 Volvo XC90 2.5 L5 GAS, CC:2500, Fuel Injection
- 2003 Volvo XC90 2.9 L6 GAS, CC:2917, Fuel Injection
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Volvo XC90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Volvo XC90 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Left Side -> Rear -> Right Side
Vehicle: 2003 Volvo XC90 2.9 L6 GAS
Left Side
- Raise and support vehicle on lift.
- On models with AWD, remove drain plug and drain transmission fluid.
- On all models, remove front wheel lug nuts.
- Remove bolt for wheel hub driveshaft.
- Counterhold using a suitable tool in brake disc vents.
- Tap end of drive shaft approximately 20-25mm into wheel hub.
- Remove nut for ball joint and control arm. If ball joint pinion moves, counterhold end of lug using suitable tool.
- Disconnect ball joint pinion from control arm using suitable tool.
- Install cap nut using suitable tool on ball joint pinion.
- Tighten nut against control arm, the...
CLICK HERE TO GET FULL ACCESS TO 2003 Volvo XC90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Volvo XC90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Volvo XC90 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2003 Volvo XC90 2.9 L6 GAS
- Raise and support vehicle on lift.
- Remove front member from body, exhaust pipe and Three-Way Catalytic Converter.
- Remove brake pipe from mountings in member. If the same driveshaft is to be reinstalled. Mark the driveshaft CV joint in relation to the bevel gear flange.
- Support front section of exhaust pipe so as not to put strain on exhaust manifold.
- Remove rear exhaust system assembly.
- Remove bolts from joint using suitable tool to hold driveline while removing bolts.
- Leave one bolt in place by a few threads for safety.
- On models with vibration dampner, hold driveline with suitab...
CLICK HERE TO GET FULL ACCESS TO 2003 Volvo XC90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Volvo XC90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Volvo XC90 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2003 Volvo XC90 2.5 L5 GAS
- Raise and support vehicle.
- Remove front member from body, exhaust pipe and Three-Way Catalytic Converter (TWC).
- Remove brake pipe from mountings in member. If same propeller shaft is to be reinstalled, mark propeller shaft CV joint in relation to bevel gear flange.
- Remove screws from propeller shaft. Use a suitable counterhold tool.
- Support front section of exhaust pipe so as not to put strain on exhaust manifold.
- Remove rear exhaust system assembly. If same propeller shaft is to be reused, mark propeller shaft CV joint in relation to flange.
- Remove screws from joint. Use a suitab...
CLICK HERE TO GET FULL ACCESS TO 2003 Volvo XC90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Volvo XC90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Volvo XC90 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Left Side -> Rear -> Right Side
Vehicle: 2003 Volvo XC90 2.5 L5 GAS
- Raise and support vehicle.
- Remove front member from body, exhaust pipe and three-way catalytic converter (TWC).
- Remove brake pipe from mountings in member.
- Remove front propeller shaft. If same propeller shaft is to be reinstalled, mark propeller shaft CV joint in relation to bevel gear flange.
- Remove screws from propeller shaft. Use a suitable counterhold tool.
- Remove rear section of exhaust system.
- Support front section of exhaust pipe so as not to put strain on exhaust manifold.
- Remove rear exhaust system assembly.
- Remove rear propeller shaft. If same propeller shaft is to be reu...
CLICK HERE TO GET FULL ACCESS TO 2003 Volvo XC90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2003 Volvo XC90 vehicle.
|
| Access the Complete guide! |
