Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2005 Chevrolet Impala car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2005 Chevrolet Impala automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2005 Chevrolet Impala
- 2005 Chevrolet Impala 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:K
- 2005 Chevrolet Impala 3.4 V6 GAS, CID:207, Fuel Injection, Aspiration:207, Engine VIN:, Desg:E
- 2005 Chevrolet Impala LS 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:K
- 2005 Chevrolet Impala SS 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:1
BRAKE SERVICE PROCEDURES FOR 2005 Chevrolet Impala AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Chevrolet Impala cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Bleed Sequence -> Manual -> Pressure
Vehicle: 2005 Chevrolet Impala 3.4 V6 GAS
Brake fluid is corrosive to painted surfaces. Care must be taken not to allow brake fluid to come in contact with painted surfaces on vehicle.
When bleeding the brake system, always bleed righthand rear wheel circuit first, followed by the lefthand front, lefthand rear and, finally, righthand front.
Manual
Pressure bleeding is recommended for all hydraulic systems. However, if a pressure bleeder is unavailable, use the following procedure. Brake fluid damages painted surfaces. Immediately clean any spilled fluid.
- Remove vacuum reserve by pumping brakes several times with engine o...
CLICK HERE TO GET FULL ACCESS TO 2005 Chevrolet Impala BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Chevrolet Impala AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Chevrolet Impala cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Aura, Bonneville, DTS, ION, LeSabre, Lucerne, Park Avenue, Solstice & SKY -> Aveo -> Corvette -> CTS -> Disassemble -> Except Aura, Aveo, Bonneville, Cobalt, Corvette, CTS, DTS, G5, ION, L-Series, LaCrosse, LeSabre, Lucerne, Park Avenue, Solstice, SKY, STS, Vibe & XLR -> L-Series -> LaCrosse, STS & XLR -> Master Cylinder Overhaul -> Vibe -> Wheel Cylinder Overhaul
Vehicle: 2005 Chevrolet Impala SS 3.8 V6 GAS
Master Cylinder Overhaul
Except Aura, Aveo, Bonneville, Cobalt, Corvette, CTS, DTS, G5, ION, L-Series, LaCrosse, LeSabre, Lucerne, Park Avenue, Solstice, SKY, STS, Vibe & XLR
Disassemble
Refer to Figs. and when performing the following procedures.
- Disconnect and plug hydraulic lines.
- Remove mounting nuts and master cylinder.
- Remove reservoir cover and diaphragm. Discard old brake fluid.
- Inspect cover and diaphragm.
- Remove fluid level switch.
- On models equipped with compact master cylinder,remove proportioning valve, Fig. .
- On all models, depress primary piston and remove lock ring.
- Plu...
CLICK HERE TO GET FULL ACCESS TO 2005 Chevrolet Impala BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Chevrolet Impala AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Chevrolet Impala cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Except ION & L-Series -> ION -> L-Series -> Master Cylinder
Vehicle: 2005 Chevrolet Impala 3.8 V6 GAS
Master Cylinder
Except ION & L-Series
- On Vibe models, remove air filer hose clamp and hose from throttle body.
- On all models, disconnect fluid level sensor retainer and electrical connector.
- Drain master cylinder reservoir brake fluid into suitable container.
- Plug hose.
- Disconnect master cylinder brake pipes. Plug open pipes.
- Remove mounting nuts and master cylinder.
- Remove reservoir, as required.
- Reverse procedure to install. Bleed hydraulic system as outlined in .
ION
- Remove underhood electrical center cover.
- Remove Connector Position Assurance (CPA) connector from brake fluid level...
CLICK HERE TO GET FULL ACCESS TO 2005 Chevrolet Impala BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Chevrolet Impala AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Chevrolet Impala cars and light trucks from 1990+.
Hydraulic Brake Systems -> Hydraulic Brake System Flush
Vehicle: 2005 Chevrolet Impala LS 3.8 V6 GAS
If brake fluid is old, rusty or contaminated or whenever new components are installed in hydraulic system, the system must be flushed. Bleed brakes...
CLICK HERE TO GET FULL ACCESS TO 2005 Chevrolet Impala BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Chevrolet Impala AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Chevrolet Impala cars and light trucks from 1990+.
Disc Brakes -> AC-Delco Single Piston Front Disc Brake -> Caliper Service -> Assemble -> Disassemble -> Inspection -> Replacement
Vehicle: 2005 Chevrolet Impala SS 3.8 V6 GAS
Replacement
- Remove approximately 2/3 of brake fluid from master cylinder.
- Raise and support front of vehicle, then remove wheel and tire assembly.
- Push piston back into caliper bore using suitable C-clamp, Fig. .
- Remove inlet fitting mounting bolt, copper washer and inlet fitting from caliper housing. Plug opening in inlet fitting. Do not crimp brake hose.
- Remove caliper mounting bolts and caliper, Fig. . If there are signs of corrosion, replace bolts when installing caliper assembly.
- Reverse procedure to install.
Disassemble
- Clean outside of caliper, then drain brake fluid from caliper...
CLICK HERE TO GET FULL ACCESS TO 2005 Chevrolet Impala BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Chevrolet Impala AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Chevrolet Impala cars and light trucks from 1990+.
Disc Brakes -> AC-Delco Single Piston Front Disc Brake -> Troubleshooting
Vehicle: 2005 Chevrolet Impala 3.8 V6 GAS
The most common cause of brake chatter on disc brakes is a variation in disc thickness. If roughness or vibration is encountered during highway operation or if pedal pulsation is experienced at low speeds, the disc may have excessive thickness variation. To inspect for this condition, measure the disc at 12 points with a micrometer at a radius appro...
CLICK HERE TO GET FULL ACCESS TO 2005 Chevrolet Impala BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
