Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2005 Honda CR-V car and truck
repair procedures including Honda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2005 Honda CR-V automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2005 Honda CR-V
- 2005 Honda CR-V EX 2.4 L4 GAS, CC:2400, Fuel Injection
- 2005 Honda CR-V LX 2.4 L4 GAS, CC:2400, Fuel Injection
- 2005 Honda CR-V SE 2.4 L4 GAS, CC:2400, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 2005 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Honda CR-V cars and light trucks from 1990+.
Honda -> Power Brake Units -> Adjustments -> Pushrod Clearance -> Pushrod Length
Vehicle: 2005 Honda CR-V SE 2.4 L4 GAS
Pushrod Clearance
Master cylinder pushrod-to-piston clearance must be inspected and adjusted before installing master cylinder.
- Adjust bolt so top of it is flush with end of master cylinder piston using pushrod adjustment gauge tool No. 07JAG-SD40100, or equivalent, Fig. .
- Install master cylinder rod seal between pushrod bolt adjustment gauge and brake booster.
- Without disturbing position of adjusting bolts, install gauge upside down on booster and torque nuts to 11 ft. lbs.
- Connect booster in line with a vacuum gauge, and maintain an engine speed that will deliver 20 inch...
CLICK HERE TO GET FULL ACCESS TO 2005 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Honda CR-V cars and light trucks from 1990+.
Honda -> Drum Brakes -> Parking Drum Brake Shoe, Replace
Vehicle: 2005 Honda CR-V LX 2.4 L4 GAS
- Raise and support vehicle, then remove rear tire and wheel assemblies.
- Remove caliper shield and disconnect parking brake cable.
- Remove banjo bolt and disconnect brake hose.
- Remove two mounting bolts and caliper.
- Disconnect and remove upper return springs.
- Remove retainers and tension pins.
- Disconnect rod spring and remove connecting rod.
- Remove lower return spring, adjuster and forward brake shoe.
- Disconnect parking brake cable from ...
CLICK HERE TO GET FULL ACCESS TO 2005 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Honda CR-V cars and light trucks from 1990+.
Honda -> Disc Brakes -> Caliper Service -> Assemble -> Disassemble -> Front -> Overhaul -> Rear -> Replace
Vehicle: 2005 Honda CR-V SE 2.4 L4 GAS
Front
Replace
- Raise and support front of vehicle, then remove tire and wheel assemblies.
- Remove banjo bolt and disconnect brake hose.
- Remove mounting bolts and caliper.
- Reverse procedure to install.
Overhaul
Disassemble
- Remove pad spring.
- Place suitable wooden block or shop rag in caliper opposite piston, then carefully remove piston from caliper by applying air pressure through brake line hole with OSHA-approved 30 psi nozzle.
- Remove boot clip, piston boot and piston seal.
Assemble
- Clean piston and caliper bore with brake fluid, then inspect for wear or damage.
- Apply brake cylinder grease t...
CLICK HERE TO GET FULL ACCESS TO 2005 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Honda CR-V cars and light trucks from 1990+.
Honda -> Disc Brakes -> Tightening Specifications
Vehicle: 2005 Honda CR-V LX 2.4 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 2005 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Honda CR-V cars and light trucks from 1990+.
Honda -> Power Brake Units -> Description
Vehicle: 2005 Honda CR-V SE 2.4 L4 GAS
The vacuum assist diaphragm assembly multiplies the force exerted on the master cylinder piston in order to increase the hydraulic pressure delivered to the wheel cylinders. The assembly also decreases the effort required to obtain acceptable stopping performance. Vacuum assist units get their energy...
CLICK HERE TO GET FULL ACCESS TO 2005 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Honda CR-V cars and light trucks from 1990+.
Honda -> Disc Brakes -> Tightening Specifications
Vehicle: 2005 Honda CR-V EX 2.4 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 2005 Honda CR-V BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2005 Honda CR-V vehicle.
|
| Access the Complete guide! |
