Auto Parts Search
We have info for following modifications of 2006 Chrysler Pacifica
- 2006 Chrysler Pacifica 3.5 V6 GAS, CC:3497, CID:215, Fuel Injection, Aspiration:215, Engine VIN:, Desg:4
- 2006 Chrysler Pacifica Touring 3.5 V6 GAS, CC:3497, CID:215, Fuel Injection, Aspiration:215, Engine VIN:, Desg:4
- 2006 Chrysler Pacifica Limited 3.5 V6 GAS, CC:3497, CID:215, Fuel Injection, Aspiration:215, Engine VIN:, Desg:4
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chrysler Pacifica AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chrysler Pacifica cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Chrysler Pacifica Limited 3.5 V6 GAS
Propeller shaft removal is a two-man operation. Never allow propeller shaft to hang from the center bearing, or while only connected to power transfer unit (PTU) or rear driveline module flanges. A helper is required. If a propshaft section is hung unsupported, damage may occur to the joint, boot, and/or center bearing from over-angulation. This may result in driveline vibrations.
- Raise vehicle on hoist.
- Remove hanger at rear muffler.
- Remove exhaust system center hanger brackets and support exhaust system with screw jack.
- Make sure transaxle is in neutral (N) . Using chalk, mark...
CLICK HERE TO GET FULL ACCESS TO 2006 Chrysler Pacifica DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chrysler Pacifica AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chrysler Pacifica cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Chrysler Pacifica 3.5 V6 GAS
Propeller shaft removal is a two-man operation. Never allow propeller shaft to hang from the center bearing, or while only connected to power transfer unit (PTU) or rear driveline module flanges. A helper is required. If a propshaft section is hung unsupported, damage may occur to the joint, boot, and/or center bearing from over-angulation. This may result in driveline vibrations.
- Raise vehicle on hoist.
- Remove hanger at rear muffler.
- Remove exhaust system center hanger brackets and support exhaust system with screw jack.
- Make sure transaxle is in neutral (N) . Using chalk, mark...
CLICK HERE TO GET FULL ACCESS TO 2006 Chrysler Pacifica DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chrysler Pacifica AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chrysler Pacifica cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Install -> Rear -> Remove
Vehicle: 2006 Chrysler Pacifica Touring 3.5 V6 GAS
Front
- Raise and support vehicle.
- Remove cotter pin and nut lock from end of half shaft.
- Remove wheel and tire assembly from vehicle.
- Remove wave washer from end of half shaft.
- With vehicle's brakes applied to keep hub from turning, loosen and remove half shaft nut.
- Remove two front disc brake caliper adapter to steering knuckle attaching bolts.
- Remove disc brake caliper assembly from steering knuckle. Caliper assembly is removed by first rotating top of caliper assembly away from steering knuckle and then removing bottom of assembly out from under machined abutment on steering k...
CLICK HERE TO GET FULL ACCESS TO 2006 Chrysler Pacifica DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chrysler Pacifica AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chrysler Pacifica cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Install -> Rear -> Remove
Vehicle: 2006 Chrysler Pacifica 3.5 V6 GAS
Front
- Raise and support vehicle.
- Remove cotter pin and nut lock from end of half shaft.
- Remove wheel and tire assembly from vehicle.
- Remove wave washer from end of half shaft.
- With vehicle's brakes applied to keep hub from turning, loosen and remove half shaft nut.
- Remove two front disc brake caliper adapter to steering knuckle attaching bolts.
- Remove disc brake caliper assembly from steering knuckle. Caliper assembly is removed by first rotating top of caliper assembly away from steering knuckle and then removing bottom of assembly out from under machined abutment on steering k...
CLICK HERE TO GET FULL ACCESS TO 2006 Chrysler Pacifica DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chrysler Pacifica AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chrysler Pacifica cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Chrysler Pacifica Touring 3.5 V6 GAS
Propeller shaft removal is a two-man operation. Never allow propeller shaft to hang from the center bearing, or while only connected to power transfer unit (PTU) or rear driveline module flanges. A helper is required. If a propshaft section is hung unsupported, damage may occur to the joint, boot, and/or center bearing from over-angulation. This may result in driveline vibrations.
- Raise vehicle on hoist.
- Remove hanger at rear muffler.
- Remove exhaust system center hanger brackets and support exhaust system with screw jack.
- Make sure transaxle is in neutral (N) . Using chalk, mark...
CLICK HERE TO GET FULL ACCESS TO 2006 Chrysler Pacifica DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chrysler Pacifica AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chrysler Pacifica cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Install -> Rear -> Remove
Vehicle: 2006 Chrysler Pacifica Limited 3.5 V6 GAS
Front
- Raise and support vehicle.
- Remove cotter pin and nut lock from end of half shaft.
- Remove wheel and tire assembly from vehicle.
- Remove wave washer from end of half shaft.
- With vehicle's brakes applied to keep hub from turning, loosen and remove half shaft nut.
- Remove two front disc brake caliper adapter to steering knuckle attaching bolts.
- Remove disc brake caliper assembly from steering knuckle. Caliper assembly is removed by first rotating top of caliper assembly away from steering knuckle and then removing bottom of assembly out from under machined abutment on steering k...
CLICK HERE TO GET FULL ACCESS TO 2006 Chrysler Pacifica DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2006 Chrysler Pacifica vehicle. |
Access the Complete guide! |