Auto Parts Search
2006 Ford Crown Victoria CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
BRAKE SERVICE PROCEDURES FOR 2006 Ford Crown Victoria AUTOMOBILES
Hydraulic Brake Systems -> Clutch System Bleeding
Vehicle: 2006 Ford Crown Victoria 4.6 V8 GAS
- Attach a rubber drain hose to bleeder screw of clutch master cylinder, then submerge free end of hose in a container partially filled with clean brake fluid.
- Slowly pump clutch pedal to floor several times and hold it.
- With clutch pedal held to floor,...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 2006 Ford Crown Victoria AUTOMOBILES
Ford Motor Co. Passenger Cars -> Fuel Filter Replacement -> Except 2002-05 Thunderbird, 2000-06 LS, 1984-87 Escort, Tracer, Tempo & Topaz 2.0L Diesel Engine & 1984-85 Continental & Mark VI 2.4L Diesel Engine
Vehicle: 2006 Ford Crown Victoria LX 4.6 V8 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
When installing the fuel filter, ensure the flow arrow is facing in the pro...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Ford Crown Victoria AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2006 Ford Crown Victoria Police Interceptor 4.6 V8 GAS
To maintain proper drive line balance, mark driveshaft, universal joints, slip yoke and companion flange before removing shaft so it can be installed in its original position.
- Raise and support vehicle.
- Index-mark rear axle pinion flange and driveshaft centering socket yoke.
- Remove four bolts.
- The driveshaft centering socket yoke fits tightly on the rear axle pinion flange pilot. Never hammer on the driveshaft or any of its components to disconnect the yoke from the flange. Using a suitable to...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2006 Ford Crown Victoria AUTOMOBILES
Alternator, Replace
Vehicle: 2006 Ford Crown Victoria Police Interceptor 4.6 V8 GAS
- Disconnect battery ground cable at battery.
- Release tension and remove accessory drive belt from alternator pulley.
- Remove pin-type retainer and release wiring harness from alternator bracket.
- Remove nut and disconnect alternator electrical connectors.
- Position cover aside.
- Remove alt...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Ford Crown Victoria AUTOMOBILES
Ford Motor Co. Cars -> Message Center -> Crown Victoria, Grand Marquis & Town Car
Vehicle: 2006 Ford Crown Victoria LX Sport 4.6 V8 GAS
The message center may be located to the right of the instrument cluster, or it may be a part of the cluster itself. It consists of three buttons: Select, E/M and Reset. The E/M button switches the display betw...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2006 Ford Crown Victoria AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2006 Ford Crown Victoria 4.6 V8 GAS
Inlet
- Drain cooling system into a suitable container.
- Reposition heater hose inlet clamp at heater core.
- Remove heater inlet hose from heater core.
- Reposition heater core inlet hose clamp at intake manifold.
- Remove hose from intake manifold.
- Remove hose from vehicle.
- Reverse procedure to install.
Ou...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2006 Ford Crown Victoria AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2006 Ford Crown Victoria LX 4.6 V8 FLEX
- Rotate tensioner away from belt using a breaker bar installed in 1/2 inch square hole in tensioner arm.
- Lift old belt over alternator pulley...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2006 Ford Crown Victoria AUTOMOBILES
Component location diagrams for most 2006 Ford Crown Victoria cars and light trucks sold in the U.S. from 1990+.
Engine Compartment Components Diagram for 2006 Ford Crown Victoria LX 4.6 V8 GAS Components on diagram: |
Engine Compartment Components Diagram for 2006 Ford Crown Victoria LX 4.6 V8 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2006 Ford Crown Victoria AUTOMOBILES
OEM drawn wiring diagrams for most 2006 Ford Crown Victoria cars and light trucks sold in the U.S.
2006 Ford Crown Victoria LX Sport 4.6 V8 GAS Wiring Diagram Components on diagram: |
2006 Ford Crown Victoria LX 4.6 V8 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2006 Ford Crown Victoria AUTOMOBILES
OEM TSB listings for most 2006 Ford Crown Victoria cars and light trucks sold in the U.S. from 1985+.
Document: MIL ON - P0506 AND/OR P0505 - HESITATION / LOSS OF RPM / DIFFICULTY STARTING / LOW IDLE RPM - REVISED Vehicle: 2006 Ford Crown Victoria 4.6 V8 GAS Symptoms: |
Document: MIL ON - DTC P2106 AND P061B - POLICE INTERCEPTOR Vehicle: 2006 Ford Crown Victoria Police Interceptor 4.6 V8 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2006 Ford Crown Victoria AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2006 Ford Crown Victoria cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2006 Ford Crown Victoria cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2006 Ford Crown Victoria cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2006 Ford Crown Victoria cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Crown Victoria SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2006 Ford Crown Victoria vehicle. |
Access the Complete guide! |