Auto Parts Search
2006 Saab 9-7X CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Saab REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service

FUEL FILTER REPLACEMENT PROCEDURES FOR 2006 Saab 9-7X AUTOMOBILES
Saab -> Fuel Filter Replacement -> 9-7X -> Fuel System Pressure Relief -> Removal & Installation
Vehicle: 2006 Saab 9-7X 4.2I 4.2 L6 GAS
Fuel System Pressure Relief
- Loosen fuel tank filler cap to relieve tank pressure.
- Connect a suitable fuel pressure gauge to fuel pressure service port located on fuel rail. Wrap a shop towel around fitting while connecting gauge to avoid fuel spillage.
- Install bleed hose into a suitable container, then open valve to bleed fuel system pressure.
- After fuel system has bleed down, remove fuel pressure gauge.
- Disconnect battery ground cable.
Removal & Installation
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixt...
CLICK HERE TO GET FULL ACCESS TO 2006 Saab 9-7X FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Saab 9-7X AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2006 Saab 9-7X 4.2I 4.2 L6 GAS
- Unlock steering column so that steering linkage is free to move.
- Raise the vehicle. Support vehicle with suitable safety stands.
- Remove front tire and wheel assemblies.
- In order to prevent drive axle from turning, insert a drift through brake caliper and into one of the rotor vanes.
- Remove axle nut and washer.
- Remove drift from brake rotor.
- Remove front brake rotors and support caliper with piece of wire in order to prevent damage to brake hose.
- Remove brackets from upper control arm holding both ABS wire and brake hose.
- Remove ABS bracket located on top of upper control arm ball...
CLICK HERE TO GET FULL ACCESS TO 2006 Saab 9-7X DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Saab 9-7X AUTOMOBILES
Reset Procedures
Vehicle: 2006 Saab 9-7X 5.3I 5.3 V8 GAS
When the Tire Pressure Monitor system detects a significant loss of tire pressure, the CHECK TIRE PRESSURE message is displayed on the DIC (Driver Inform...
CLICK HERE TO GET FULL ACCESS TO 2006 Saab 9-7X TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2006 Saab 9-7X AUTOMOBILES
Alternator, Replace
Vehicle: 2006 Saab 9-7X 5.3I 5.3 V8 GAS
- Disconnect battery ground cable.
- Disconnect positive crankcase ventilation (PCV) fresh air tube from air cleaner resonator outlet duct.
- Loosen air cleaner outlet duct clamps at mass air flow (MAF)/Intake Air Temperature (IAT) sensor and at throttle body.
- Remove air cleaner outlet duct bolt and duct.
- Remove drive belt.
- Disconnect engine wiring harness electrical connector from al...
CLICK HERE TO GET FULL ACCESS TO 2006 Saab 9-7X STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Saab 9-7X AUTOMOBILES
Saab -> Engine Oil Life Monitor -> 2005-06 9-7x
Vehicle: 2006 Saab 9-7X 4.2I 4.2 L6 GAS
The Engine Oil Life monitor indicates when an oil and filter change are needed.
The monitor will not detect dust in the oil. If operating in dusty conditions be sure to change the oil and filter every 3000 miles or sooner if the CHANGE OIL SOON lamp lights.
To reset the Engine Oil Life monitor proceed as follows:
- Use the fuel button on the DIC (Driver I...
CLICK HERE TO GET FULL ACCESS TO 2006 Saab 9-7X MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2006 Saab 9-7X AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2006 Saab 9-7X 5.3I 5.3 V8 GAS
Inlet
- Drain cooling system into a suitable container.
- Reposition heater core inlet hose clamp at intake manifold fitting.
- Remove hose from intake manifold fitting.
- Reposition heater hose inlet clamp at heater core.
- Remove heater inlet hose from heater core.
- Remove hose from vehicle.
- Reverse pr...
CLICK HERE TO GET FULL ACCESS TO 2006 Saab 9-7X RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2006 Saab 9-7X AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2006 Saab 9-7X 5.3I 5.3 V8 GAS
- Remove air cleaner resonator outlet duct assembly by doing the following:
- Disconnect PVC valve, fresh air tube from air cleaner resonator outlet duct.
- Loosen clamps at MAF and IAT sensors.
- Remove bolt for air clean...
CLICK HERE TO GET FULL ACCESS TO 2006 Saab 9-7X SERPENTINE BELT SERVICE PROCEDURES
WIRING DIAGRAMS FOR 2006 Saab 9-7X AUTOMOBILES
OEM drawn wiring diagrams for most 2006 Saab 9-7X cars and light trucks sold in the U.S.
![]() Components on diagram: |
![]() Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Saab 9-7X WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2006 Saab 9-7X AUTOMOBILES
OEM TSB listings for most 2006 Saab 9-7X cars and light trucks sold in the U.S. from 1985+.
Document: Engine Rattle Noise after R And R of the Crankshaft Balancer -Inspect Bolt Torque Vehicle: 2006 Saab 9-7X 4.2I 4.2 L6 GAS Symptoms: |
Document: GM of Canada New Vehicle Limited Warranty Tire Program Vehicle: 2006 Saab 9-7X 4.2I 4.2 L6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2006 Saab 9-7X TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2006 Saab 9-7X AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2006 Saab 9-7X cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2006 Saab 9-7X cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2006 Saab 9-7X cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2006 Saab 9-7X cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2006 Saab 9-7X SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
![]() |
Access the Complete guide! |