Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2006 Subaru Legacy car and truck
repair procedures including Subaru engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2006 Subaru Legacy automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2006 Subaru Legacy
- 2006 Subaru Legacy GT 2.5 H4 GAS, CC:2458, Fuel Injection
- 2006 Subaru Legacy 2.5I 2.5 H4 GAS, CC:2458, Fuel Injection
- 2006 Subaru Legacy GT Spec.b 2.5 H4 GAS, CC:2458, Fuel Injection
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Subaru Legacy AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Subaru Legacy cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2006 Subaru Legacy GT Spec.b 2.5 H4 GAS
Front
- Disconnect battery ground cable.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Unstake hub nut using suitable tool.
- Remove driveshaft locknut from front hub while depressing brake pedal. Remove wheel before loosening axle nut.
- Remove stabilizer link from front arm.
- Remove brake caliper bolts and support caliper to strut housing using mechanics wire.
- Remove disc brake rotor. If brake rotor is difficult to remove, drive 8mm bolt into threaded end of rotor, then remove the rotor. Reference mark surface of h...
CLICK HERE TO GET FULL ACCESS TO 2006 Subaru Legacy DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Subaru Legacy AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Subaru Legacy cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2006 Subaru Legacy 2.5I 2.5 H4 GAS
Front
- Disconnect battery ground cable.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Unstake hub nut using suitable tool.
- Remove driveshaft locknut from front hub while depressing brake pedal. Remove wheel before loosening axle nut.
- Remove stabilizer link from front arm.
- Remove brake caliper bolts and support caliper to strut housing using mechanics wire.
- Remove disc brake rotor. If brake rotor is difficult to remove, drive 8mm bolt into threaded end of rotor, then remove the rotor. Reference mark surface of h...
CLICK HERE TO GET FULL ACCESS TO 2006 Subaru Legacy DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Subaru Legacy AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Subaru Legacy cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2006 Subaru Legacy GT 2.5 H4 GAS
Front
- Disconnect battery ground cable.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Unstake hub nut using suitable tool.
- Remove driveshaft locknut from front hub while depressing brake pedal. Remove wheel before loosening axle nut.
- Remove stabilizer link from front arm.
- Remove brake caliper bolts and support caliper to strut housing using mechanics wire.
- Remove disc brake rotor. If brake rotor is difficult to remove, drive 8mm bolt into threaded end of rotor, then remove the rotor. Reference mark surface of h...
CLICK HERE TO GET FULL ACCESS TO 2006 Subaru Legacy DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Subaru Legacy AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Subaru Legacy cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Subaru Legacy GT Spec.b 2.5 H4 GAS
Wrap metal parts with a cloth or rubber material. Rubber boot may be damaged due to interference with adjacent metal parts during removal.
- Disconnect battery ground cable.
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove center exhaust pipes bolts and nuts.
- Remove rear exhaust pipe and muffler.
- Remove heat shield cover.
- Remove differential mount front cover bolts, then remove mount.
- Place reference mark on front driveline and rear differential flange. Paint is recommended for match marks. Never da...
CLICK HERE TO GET FULL ACCESS TO 2006 Subaru Legacy DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Subaru Legacy AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Subaru Legacy cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Subaru Legacy 2.5I 2.5 H4 GAS
Wrap metal parts with a cloth or rubber material. Rubber boot may be damaged due to interference with adjacent metal parts during removal.
- Disconnect battery ground cable.
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove center exhaust pipes bolts and nuts.
- Remove rear exhaust pipe and muffler.
- Remove heat shield cover.
- Remove differential mount front cover bolts, then remove mount.
- Place reference mark on front driveline and rear differential flange. Paint is recommended for match marks. Never da...
CLICK HERE TO GET FULL ACCESS TO 2006 Subaru Legacy DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Subaru Legacy AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Subaru Legacy cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Subaru Legacy GT 2.5 H4 GAS
Wrap metal parts with a cloth or rubber material. Rubber boot may be damaged due to interference with adjacent metal parts during removal.
- Disconnect battery ground cable.
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove center exhaust pipes bolts and nuts.
- Remove rear exhaust pipe and muffler.
- Remove heat shield cover.
- Remove differential mount front cover bolts, then remove mount.
- Place reference mark on front driveline and rear differential flange. Paint is recommended for match marks. Never da...
CLICK HERE TO GET FULL ACCESS TO 2006 Subaru Legacy DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2006 Subaru Legacy vehicle.
|
| Access the Complete guide! |
