Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2006 Volvo XC90 car and truck
repair procedures including Volvo engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2006 Volvo XC90 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2006 Volvo XC90
- 2006 Volvo XC90 V8 4.4 V8 GAS, CC:4414, CID:269, Fuel Injection, Aspiration:269
- 2006 Volvo XC90 2.5T 2.5 L5 GAS, CC:2521, Fuel Injection
- 2006 Volvo XC90 V8 Ocean Race 4.4 V8 GAS, CC:4414, CID:269, Fuel Injection, Aspiration:269
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Volvo XC90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Volvo XC90 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Left Side -> Rear -> Right Side
Vehicle: 2006 Volvo XC90 2.5T 2.5 L5 GAS
Left Side
- Raise and support vehicle on lift.
- Remove hub cap.
- Remove front wheel lug nuts.
- Remove bolt for wheel hub driveshaft.
- Tap end of drive shaft approximately 15-20mm into wheel hub.
- Remove anti-roll bar strut from spring strut.
- Counterhold ball joint pinion so that ball joint boot cannot turn.
- Detach brake hose from its mounting lug in spring strut.
- Detach ABS line from its mounting lug in wheel arch.
- Slacken off nut for ball joint for control arm. Before removing the nuts from the ball joints, clean the exposed threads of rust. Lubricate using rust solvent before removing t...
CLICK HERE TO GET FULL ACCESS TO 2006 Volvo XC90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Volvo XC90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Volvo XC90 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Volvo XC90 V8 4.4 V8 GAS
- Raise and support vehicle on lift.
- Remove front member from body, exhaust pipe and Three-Way Catalytic Converter.
- Remove brake pipe from mountings in member. If the same driveshaft is to be reinstalled. Mark the driveshaft CV joint in relation to the bevel gear flange.
- Support front section of exhaust pipe so as not to put strain on exhaust manifold.
- Remove rear exhaust system assembly.
- Remove bolts from joint using suitable tool to hold driveline while removing bolts.
- Leave one bolt in place by a few threads for safety.
- On models with vibration dampner, hold driveline with suitab...
CLICK HERE TO GET FULL ACCESS TO 2006 Volvo XC90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Volvo XC90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Volvo XC90 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Left Side -> Rear -> Right Side
Vehicle: 2006 Volvo XC90 V8 Ocean Race 4.4 V8 GAS
Left Side
- Raise and support vehicle on lift.
- On models with AWD, remove drain plug and drain transmission fluid.
- On all models, remove front wheel lug nuts.
- Remove bolt for wheel hub driveshaft.
- Counterhold using a suitable tool in brake disc vents.
- Tap end of drive shaft approximately 20-25mm into wheel hub.
- Remove nut for ball joint and control arm. If ball joint pinion moves, counterhold end of lug using suitable tool.
- Disconnect ball joint pinion from control arm using suitable tool.
- Install cap nut using suitable tool on ball joint pinion.
- Tighten nut against control arm, the...
CLICK HERE TO GET FULL ACCESS TO 2006 Volvo XC90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Volvo XC90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Volvo XC90 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Left Side -> Rear -> Right Side
Vehicle: 2006 Volvo XC90 V8 4.4 V8 GAS
Left Side
- Raise and support vehicle on lift.
- On models with AWD, remove drain plug and drain transmission fluid.
- On all models, remove front wheel lug nuts.
- Remove bolt for wheel hub driveshaft.
- Counterhold using a suitable tool in brake disc vents.
- Tap end of drive shaft approximately 20-25mm into wheel hub.
- Remove nut for ball joint and control arm. If ball joint pinion moves, counterhold end of lug using suitable tool.
- Disconnect ball joint pinion from control arm using suitable tool.
- Install cap nut using suitable tool on ball joint pinion.
- Tighten nut against control arm, the...
CLICK HERE TO GET FULL ACCESS TO 2006 Volvo XC90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Volvo XC90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Volvo XC90 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Volvo XC90 2.5T 2.5 L5 GAS
- Raise and support vehicle on lift.
- Remove front member from body, exhaust pipe and Three-Way Catalytic Converter.
- Remove brake pipe from mountings in member. If the same driveshaft is to be reinstalled. Mark the driveshaft CV joint in relation to the bevel gear flange.
- Support front section of exhaust pipe so as not to put strain on exhaust manifold.
- Remove rear exhaust system assembly.
- Remove bolts from joint using suitable tool to hold driveline while removing bolts.
- Leave one bolt in place by a few threads for safety.
- On models with vibration dampner, hold driveline with suitab...
CLICK HERE TO GET FULL ACCESS TO 2006 Volvo XC90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Volvo XC90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Volvo XC90 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Volvo XC90 V8 Ocean Race 4.4 V8 GAS
- Raise and support vehicle on lift.
- Remove front member from body, exhaust pipe and Three-Way Catalytic Converter.
- Remove brake pipe from mountings in member. If the same driveshaft is to be reinstalled. Mark the driveshaft CV joint in relation to the bevel gear flange.
- Support front section of exhaust pipe so as not to put strain on exhaust manifold.
- Remove rear exhaust system assembly.
- Remove bolts from joint using suitable tool to hold driveline while removing bolts.
- Leave one bolt in place by a few threads for safety.
- On models with vibration dampner, hold driveline with suitab...
CLICK HERE TO GET FULL ACCESS TO 2006 Volvo XC90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2006 Volvo XC90 vehicle.
|
| Access the Complete guide! |
