Auto Parts Search
2007 Mazda 6 CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Mazda REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Mazda 6 AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2007 Mazda 6 S 3.0 V6 GAS
Performing the following procedures without first removing the ABS wheel-speed sensor may possibly cause an open circuit in the wiring harness if pulled by mistake. Before performing the following procedures, disconnect the ABS wheel speed sensor connector (axle side) and fix the wiring harness to an appropriate place where it will not be pulled by mistake while servicing vehicle.
Note: When replacing the driveshaft (double offset joint type), replace it as a single unit because it cannot be disassembled.
- Raise and support vehicle and support it with safety stands in proper...
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2007 Mazda 6 AUTOMOBILES
Component Locations
Vehicle: 2007 Mazda 6 S 3.0 V6 GAS
Refer to F...
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2007 Mazda 6 AUTOMOBILES
Starter, Replace
Vehicle: 2007 Mazda 6 S 3.0 V6 GAS
- Disconnect battery ground cable.
- Remove air cleaner hose intake clamps, disconnect MAP sensor connector, and remove bolts securing housing assembly.
- Raise vehicle on lift.
- Remove under cover bolts then remove undercover.
- On models equipped with manual transaxle, remove clutch release cylinder with pipe still connected.
- On all models, remove starter motor coolant wiring harness bracket nuts then remove bracket.
- Remove nut from starter cable B-terminal ...
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2007 Mazda 6 AUTOMOBILES
Cabin Air Filter Service -> Mazda -> 2003-09 Mazda6
Vehicle: 2007 Mazda 6 I 2.3 L4 GAS
Under normal operating conditions the cabin air filter should be replaced every 24 months or 25,000 miles. In dusty areas change the cabin air filter more often.
- Open the glove compartment assembly.
- Detach the stay damper from the glove compartment.
- Carefully push inward at both side of the ...
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2007 Mazda 6 AUTOMOBILES
Mazda -> Tire Pressure Monitoring System Indicator -> 2004-09 Mazda6 -> Relearn -> Reset
Vehicle: 2007 Mazda 6 S 3.0 V6 GAS
Reset
Adjust the tire to the recommended pressure, then drive the vehicle to reset the warning lamp.
Relearn
After changing a tire, cycle the ignition switch to the On position and then retu...
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2007 Mazda 6 AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2007 Mazda 6 S 3.0 V6 GAS
Lower
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at radiator outlet.
- Remove hose from radiator.
- Reposition hose clamp at water inlet.
- Remove hose from water inlet.
- Remove hose from vehicle.
- Reverse procedure t...
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2007 Mazda 6 AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2007 Mazda 6 I 2.3 L4 GAS
- Rotate or lift the belt tensioner arm, using a suitable tool to relieve tension from dr...
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2007 Mazda 6 AUTOMOBILES
Component location diagrams for most 2007 Mazda 6 cars and light trucks sold in the U.S. from 1990+.
Engine Compartment Diagram for 2007 Mazda 6 Mazdaspeed 2.3 L4 GAS Components on diagram: |
Door Components Diagram for 2007 Mazda 6 Mazdaspeed 2.3 L4 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2007 Mazda 6 AUTOMOBILES
OEM drawn wiring diagrams for most 2007 Mazda 6 cars and light trucks sold in the U.S.
2007 Mazda 6 I 2.3 L4 GAS Wiring Diagram Components on diagram: |
2007 Mazda 6 Mazdaspeed 2.3 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2007 Mazda 6 AUTOMOBILES
OEM TSB listings for most 2007 Mazda 6 cars and light trucks sold in the U.S. from 1985+.
Document: SERVICE POINTS FOR ENGINE REPLACEMENT DUE TO ENGINE NOISE Vehicle: 2007 Mazda 6 Mazdaspeed 2.3 L4 GAS Symptoms: |
Document: REAR QUARTER GLASS REPLACEMENT PRECAUTION Vehicle: 2007 Mazda 6 S 3.0 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2007 Mazda 6 AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2007 Mazda 6 cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2007 Mazda 6 cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2007 Mazda 6 cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2007 Mazda 6 cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2007 Mazda 6 SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2007 Mazda 6 vehicle. |
Access the Complete guide! |