Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2007 Saturn RELAY-1 car and truck
repair procedures including Saturn engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2007 Saturn RELAY-1 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2007 Saturn RELAY-1
- 2007 Saturn RELAY-1 3.9 V6 GAS, CC:3880, CID:237, Fuel Injection, Aspiration:237, Engine VIN:, Desg:1
- 2007 Saturn RELAY-1 3.9 V6 FLEX, CC:3880, CID:237, Fuel Injection, Aspiration:237, Engine VIN:, Desg:W
BRAKE SERVICE PROCEDURES FOR 2007 Saturn RELAY-1 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2007 Saturn RELAY-1 cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Troubleshooting -> Brake Rattle -> Brake Roughness Or Chatter; Pedal Pumping -> Caliper Brake Fluid Leak -> Excessive Pedal Effort -> Excessive Pedal Travel -> Heavy Brake Drag -> No Braking Effect When Brake Pedal Is Depressed -> Pull, Uneven Or Grabbing Brakes -> Rear Brakes Locking On Application
Vehicle: 2007 Saturn RELAY-1 3.9 V6 FLEX
Excessive Pedal Travel
- Worn brake linings.
- Disc pads knock back after cornering or rough road travel.
- Piston and linings not properly seated or positioned.
- Insufficient fluid in system.
- Loose wheel bearing adjustment.
- Damaged or worn caliper piston seal.
- Improper booster pushrod adjustment.
- Pads out of flat more than .005 inch.
- Rear brake automatic adjusters inoperative.
- Improperly ground rear brake shoes.
Brake Roughness Or Chatter; Pedal Pumping
- Excessive lateral runout of rotor.
- Rotor excessively out of parallel.
Excessive Pedal Effort
- Frozen or seized pistons.
- Brake fluid, oil or grease on ...
CLICK HERE TO GET FULL ACCESS TO 2007 Saturn RELAY-1 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2007 Saturn RELAY-1 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2007 Saturn RELAY-1 cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Brake System Bleed -> Manual Bleed -> Pressure Bleed
Vehicle: 2007 Saturn RELAY-1 3.9 V6 GAS
Manual Bleed
- If vehicle is equipped with power brakes, remove vacuum reserve by applying brakes several times with engine off.
- Fill master cylinder reservoirs with suitable brake fluid. Ensure to always keep master cylinder reservoirs at least half full during entire bleeding procedure.
- If master cylinder is suspected to have air in bore, it must be bled first. To bleed master cylinder, proceed as follows:
- Disconnect forward brake pipe connection at master cylinder.
- Allow brake fluid to fill master cylinder bore until it begins to flow from forward pipe connector port.
- Connect and ...
CLICK HERE TO GET FULL ACCESS TO 2007 Saturn RELAY-1 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2007 Saturn RELAY-1 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2007 Saturn RELAY-1 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Description -> Hydraulic Control Valves -> Master Cylinder
Vehicle: 2007 Saturn RELAY-1 3.9 V6 GAS
Master Cylinder
Some vehicles use a conventional tandem master cylinder with two hydraulic pistons operating in-line. The primary piston controls the front brake system and the secondary piston controls the rear brake system.
Other models use a master cylinder that operates the same as the conventional master cylinder, but also incorporates a quick take-up feature in the rear chamber to reduce excessive pedal travel which may result from increased fluid displacement required to move the low drag caliper piston out against the rotor.
The quick take-up uses a spring-loaded ball check val...
CLICK HERE TO GET FULL ACCESS TO 2007 Saturn RELAY-1 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2007 Saturn RELAY-1 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2007 Saturn RELAY-1 cars and light trucks from 1990+.
Anti-Lock Brakes -> Delphi 7.4 -> Description
Vehicle: 2007 Saturn RELAY-1 3.9 V6 GAS
When wheel slip is detected during a brake application, the ABS enters anti-lock mode. During anti-lock braking, hydraulic pressure in the individual wheel circuits is controlled to prevent any wheel from slipping. A separate hydraulic line and specific solenoid valves are provided for each wheel. The ABS can decrease, hold, or increase hydraulic pressure to each wheel brake. The ABS cannot, however, increase hydraulic pressure above the amount which is transmitted by the master cylinder during braking.
During anti-lock braking, a series of rapid pulsations is felt in the brake pedal...
CLICK HERE TO GET FULL ACCESS TO 2007 Saturn RELAY-1 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2007 Saturn RELAY-1 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2007 Saturn RELAY-1 cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> Precautions -> Connect -> Disconnect -> Hybrid Battery Service
Vehicle: 2007 Saturn RELAY-1 3.9 V6 FLEX
Hybrid Battery Service
Disconnect
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment: Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors. Certified and up-to-date Class "0" Insulation gloves rated at 1000 volts with leather protectors. Visually and functionally inspect the gloves before use. Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or not. Failure to follow the procedure exactly as written may res...
CLICK HERE TO GET FULL ACCESS TO 2007 Saturn RELAY-1 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2007 Saturn RELAY-1 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2007 Saturn RELAY-1 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Hydraulic System Flush -> Manual Bleed -> Master Cylinder Bleed -> Parking Brake Bleed -> Pressure Bleed
Vehicle: 2007 Saturn RELAY-1 3.9 V6 GAS
Manual Bleed
- If vehicle is equipped with power brakes, remove vacuum reserve by applying brakes several times with engine off.
- Fill master cylinder reservoirs with suitable brake fluid. Ensure to always keep master cylinder reservoirs at least half full during entire bleeding procedure.
- If master cylinder is suspected to have air in bore, it must be bled first. To bleed master cylinder, proceed as follows:
- Disconnect forward brake pipe connection at master cylinder.
- Allow brake fluid to fill master cylinder bore until it begins to flow from forward pipe connector port.
- Connect and ...
CLICK HERE TO GET FULL ACCESS TO 2007 Saturn RELAY-1 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
