Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 GMC Canyon car and truck
repair procedures including GMC engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 GMC Canyon automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 GMC Canyon
- 2008 GMC Canyon SLE 3.7 L5 GAS, CC:3654, CID:223, Fuel Injection, Aspiration:223, Engine VIN:, Desg:E
- 2008 GMC Canyon SLE 2.9 L4 GAS, CC:2921, CID:178, Fuel Injection, Aspiration:178, Engine VIN:, Desg:9
- 2008 GMC Canyon SL 2.9 L4 GAS, CC:2921, CID:178, Fuel Injection, Aspiration:178, Engine VIN:, Desg:9
- 2008 GMC Canyon SLT 3.7 L5 GAS, CC:3654, CID:223, Fuel Injection, Aspiration:223, Engine VIN:, Desg:E
- 2008 GMC Canyon SLT 2.9 L4 GAS, CC:2921, CID:178, Fuel Injection, Aspiration:178, Engine VIN:, Desg:9
- 2008 GMC Canyon WT 3.7 L5 GAS, CC:3654, CID:223, Fuel Injection, Aspiration:223, Engine VIN:, Desg:E
- 2008 GMC Canyon WT 2.9 L4 GAS, CC:2921, CID:178, Fuel Injection, Aspiration:178, Engine VIN:, Desg:9
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 GMC Canyon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 GMC Canyon cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Two Piece Driveshaft
Vehicle: 2008 GMC Canyon SLE 2.9 L4 GAS
Front
- Raise and support vehicle.
- Mark the front U-joint to the pinion yoke on the front differential.
- Mark the relationship of the rear U-joint to the transfer case drive flange.
- Remove the retaining nuts and bolts from the drive flange.
- Remove the clamps and retaining bolts from the front drive axle pinion flange.
- Remove the front propeller shaft from the vehicle.
- Using tape and or a rubber band, wrap the front U-joint bearing caps to ensure the caps do not separate from the U-joint.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft to the pinion flang...
CLICK HERE TO GET FULL ACCESS TO 2008 GMC Canyon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 GMC Canyon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 GMC Canyon cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2008 GMC Canyon SLT 3.7 L5 GAS
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove wheel drive shaft nut and washer. Do not reuse wheel drive shaft nut, replace with new.
- Remove steering knuckle assembly.
- Release wheel drive shaft by placing a brass drift against tripod housing. Firmly strike brass drift with a hammer to release drive shaft.
- Remove front wheel drive shaft from vehicle.
- Reverse procedure to install, noting the following:
- A snap or po...
CLICK HERE TO GET FULL ACCESS TO 2008 GMC Canyon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 GMC Canyon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 GMC Canyon cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2008 GMC Canyon SLE 2.9 L4 GAS
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove wheel drive shaft nut and washer. Do not reuse wheel drive shaft nut, replace with new.
- Remove steering knuckle assembly.
- Release wheel drive shaft by placing a brass drift against tripod housing. Firmly strike brass drift with a hammer to release drive shaft.
- Remove front wheel drive shaft from vehicle.
- Reverse procedure to install, noting the following:
- A snap or po...
CLICK HERE TO GET FULL ACCESS TO 2008 GMC Canyon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 GMC Canyon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 GMC Canyon cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2008 GMC Canyon SLE 3.7 L5 GAS
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove wheel drive shaft nut and washer. Do not reuse wheel drive shaft nut, replace with new.
- Remove steering knuckle assembly.
- Release wheel drive shaft by placing a brass drift against tripod housing. Firmly strike brass drift with a hammer to release drive shaft.
- Remove front wheel drive shaft from vehicle.
- Reverse procedure to install, noting the following:
- A snap or po...
CLICK HERE TO GET FULL ACCESS TO 2008 GMC Canyon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 GMC Canyon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 GMC Canyon cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2008 GMC Canyon SLT 2.9 L4 GAS
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove wheel drive shaft nut and washer. Do not reuse wheel drive shaft nut, replace with new.
- Remove steering knuckle assembly.
- Release wheel drive shaft by placing a brass drift against tripod housing. Firmly strike brass drift with a hammer to release drive shaft.
- Remove front wheel drive shaft from vehicle.
- Reverse procedure to install, noting the following:
- A snap or po...
CLICK HERE TO GET FULL ACCESS TO 2008 GMC Canyon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 GMC Canyon AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 GMC Canyon cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Two Piece Driveshaft
Vehicle: 2008 GMC Canyon SLT 2.9 L4 GAS
Front
- Raise and support vehicle.
- Mark the front U-joint to the pinion yoke on the front differential.
- Mark the relationship of the rear U-joint to the transfer case drive flange.
- Remove the retaining nuts and bolts from the drive flange.
- Remove the clamps and retaining bolts from the front drive axle pinion flange.
- Remove the front propeller shaft from the vehicle.
- Using tape and or a rubber band, wrap the front U-joint bearing caps to ensure the caps do not separate from the U-joint.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft to the pinion flang...
CLICK HERE TO GET FULL ACCESS TO 2008 GMC Canyon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
