Auto Parts Search
2008 Honda FIT CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Honda REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Honda FIT car and truck
repair procedures including Honda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Honda FIT automobile. Try the Automotix DIY solution today!
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Honda FIT AUTOMOBILES
CV AXLE SHAFT, Replace -> Automatic Transmission -> Manual Transmission
Vehicle: 2008 Honda FIT Sport 1.5 L4 GAS
Manual Transmission
- Raise vehicle on hoist.
- Remove wheel nuts and front wheels.
- Lift up locking tab on spindle nut then remove nut.
- Drain transmission fluid into suitable container and reinstall drain plug using a new washer.
- Separate front stabilizer link.
- Remove lock pin from lower arm ball joint castle nut, and remove nut then separate ball joint from lower arm lower arm using ball joint thread protector and remover. To avoid damaging ball joint, install ball joint thread protector onto threads of ball joint. Be careful not to damage ball joint boot when installing remover.
- R...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Honda FIT AUTOMOBILES
Relearn Procedures -> Tire Rotation -> TPMS Control Unit Or Sensor Replacement
Vehicle: 2008 Honda FIT 1.5 L4 GAS
Tire Rotation
When doing a tire rotation, memorizing the sensors in not needed.
TPMS Control Unit Or Sensor Replacement
To ensure the control unit memorizes the correct ID, the vehicle with the new sensor must be at least 10 ft. away from other vehicles that have tire pressure sensors.
- Place the ignition switch in Lock position.
- Connect Honda HDS or other suitable scan tool to the DLC (Data Link Connector) located under the LH side of the instrument panel.
- Place the ignition switch in the On position. Ensure the scan tool communicates with the TPMS control unit.
- Select Sensor ID le...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2008 Honda FIT AUTOMOBILES
Starter, Replace
Vehicle: 2008 Honda FIT Sport 1.5 L4 GAS
On models equipped with anti-lock codes for audio system, write down code for audio presets. When connecting battery ground cable upon installation you will need to enter the preset code. Ensure ignition switch is turned off.
- Disconnect battery ground cable.
- Remove oil dipstick bolt then pull up on oil dipstick tube.
- Raise vehicle on suitable lift.
- Remove plastic retainers securing splash shield.
- Re...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2008 Honda FIT AUTOMOBILES
Cabin Air Filter Service -> Honda -> 2007-09 Fit
Vehicle: 2008 Honda FIT Sport 1.5 L4 GAS
The cabin air filter should be replaced at Maintenance Minder Indicator Symbol 2. If the vehicle is operated primarily in urban areas with high concentrations of soot and diesel powered vehicles, replace the filter every 15,000 miles. The filter should be replaced more often if air flow is less than normal.
- On models equipped with radio anti-theft feature, prior to disconnecting the battery ground cable make sure you have the radio anti-theft code.
- On all models, disconnect and isolate the battery ground cable. After disconnecting the battery ground cable wait at least 3 minutes to al...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Honda FIT AUTOMOBILES
Honda -> Automatic Transmission (A/T) Fluid Temperature Indicator ->
Vehicle: 2008 Honda FIT 1.5 L4 GAS
The A/T fluid temperature lamp will turn on when ignition switch is placed in On position and should turn off after a few seconds. If lamp illuminates while driving, the vehicle should be pulled off the r...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2008 Honda FIT AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2008 Honda FIT Sport 1.5 L4 GAS
Lower
- Drain engine coolant into a suitable container.
- Reposition hose clamp and remove hose from thermostat side of water passage
- Reposition hose clamp and remove hose from radiator outlet.
- Remove hose from vehicle.
- Rever...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2008 Honda FIT AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2008 Honda FIT Sport 1.5 L4 GAS
- Loosen alternator bracket lock bolt, mounting bolt, and adjusting bolt.
- Re...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2008 Honda FIT AUTOMOBILES
Component location diagrams for most 2008 Honda FIT cars and light trucks sold in the U.S. from 1990+.
 Front Body Components Diagram for 2008 Honda FIT Sport 1.5 L4 GASComponents on diagram: |
 Body Components Diagram for 2008 Honda FIT Sport 1.5 L4 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2008 Honda FIT AUTOMOBILES
OEM drawn wiring diagrams for most 2008 Honda FIT cars and light trucks sold in the U.S.
 2008 Honda FIT 1.5 L4 GAS Wiring DiagramComponents on diagram: |
 2008 Honda FIT 1.5 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2008 Honda FIT AUTOMOBILES
OEM TSB listings for most 2008 Honda FIT cars and light trucks sold in the U.S. from 1985+.
|
Document: ATEQ VT55 TPMS Update Information Vehicle: 2008 Honda FIT Sport 1.5 L4 GAS Auto Systems: |
|
Document: High Mount Brake Light Seal Comes Loose Vehicle: 2008 Honda FIT Sport 1.5 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2008 Honda FIT AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2008 Honda FIT cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2008 Honda FIT cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2008 Honda FIT cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2008 Honda FIT cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2008 Honda FIT SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
