Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 KIA Rondo car and truck
repair procedures including KIA engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 KIA Rondo automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 KIA Rondo
- 2008 KIA Rondo LX 2.4 L4 GAS, CC:2359, Fuel Injection, Engine VIN:, Desg:5
- 2008 KIA Rondo EX 2.4 L4 GAS, CC:2359, Fuel Injection, Engine VIN:, Desg:5
- 2008 KIA Rondo LX 2.7 V6 GAS, CC:2656, Fuel Injection, Engine VIN:, Desg:6
- 2008 KIA Rondo EX 2.7 V6 GAS, CC:2656, Fuel Injection, Engine VIN:, Desg:6
- 2008 KIA Rondo EX Premium 2.4 L4 GAS, CC:2359, Fuel Injection, Engine VIN:, Desg:5
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 KIA Rondo AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 KIA Rondo cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> Tire Pressure Sensor -> TPMS Receiver
Vehicle: 2008 KIA Rondo LX 2.4 L4 GAS
Tire Pressure Sensor
Removal
- Loosen the wheel lug nuts.
- Raise and support the vehicle with jack stands.
- Remove tire and wheel assembly from vehicle.
- Deflate air from tire assembly, then remove wheel weights.
- Break tire bead 180° from valve stem. When removing tire from rim caution should be taken not to hit valve stem with tire tools.
- Remove the valve nut. Use caution when handling sensor.
- Discard valve nut.
Installation
- Use caution when handling sensor. Avoid getting any lubricant on sensor.
- Place valve in sensor and turn valve three times with square part of screw in slot. The fit ...
CLICK HERE TO GET FULL ACCESS TO 2008 KIA Rondo TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 KIA Rondo AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 KIA Rondo cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures -> Tire Pressure Sensor Initiation -> TPMS Receiver
Vehicle: 2008 KIA Rondo LX 2.4 L4 GAS
Tire Pressure Sensor Initiation
- Using Kia TPMS exciter tool, or equivalent, read the four tire pressure sensor IDs starting with sensor 1 the LH front wheel.
- Read the remaining sensors in the following order:
- Sensor 2, RH front wheel.
- Sensor 3, LH rear wheel.
- Sensor 4, RH rear wheel.
- Connect the Kia exciter tool, or equivalent, to the DLC (Data Link Connector) located under the LH side of the instrument panel.
- Using the tool, register the four sensor IDs to the TPMS receiver.
- Disconnect the tool from the DLC.
- Place the ignition switch in the Off position for 4 minutes, then turn the i...
CLICK HERE TO GET FULL ACCESS TO 2008 KIA Rondo TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 KIA Rondo AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 KIA Rondo cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures -> Tire Pressure Sensor Initiation -> TPMS Receiver
Vehicle: 2008 KIA Rondo EX 2.7 V6 GAS
Tire Pressure Sensor Initiation
- Using Kia TPMS exciter tool, or equivalent, read the four tire pressure sensor IDs starting with sensor 1 the LH front wheel.
- Read the remaining sensors in the following order:
- Sensor 2, RH front wheel.
- Sensor 3, LH rear wheel.
- Sensor 4, RH rear wheel.
- Connect the Kia exciter tool, or equivalent, to the DLC (Data Link Connector) located under the LH side of the instrument panel.
- Using the tool, register the four sensor IDs to the TPMS receiver.
- Disconnect the tool from the DLC.
- Place the ignition switch in the Off position for 4 minutes, then turn the i...
CLICK HERE TO GET FULL ACCESS TO 2008 KIA Rondo TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 KIA Rondo AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 KIA Rondo cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Identification
Vehicle: 2008 KIA Rondo LX 2.4 L4 GAS
Accessing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to DLC (Data Link Connector) and follow manufacturer's instructions.
Diagnostic Trouble Code Identification
...
CLICK HERE TO GET FULL ACCESS TO 2008 KIA Rondo TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 KIA Rondo AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 KIA Rondo cars and light trucks sold in the U.S. from mid 1990's+.
Component Locations
Vehicle: 2008 KIA Rondo LX 2.4 L4 GAS
Refer to F...
CLICK HERE TO GET FULL ACCESS TO 2008 KIA Rondo TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 KIA Rondo AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 KIA Rondo cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Identification
Vehicle: 2008 KIA Rondo LX 2.7 V6 GAS
Accessing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to DLC (Data Link Connector) and follow manufacturer's instructions.
Diagnostic Trouble Code Identification
...
CLICK HERE TO GET FULL ACCESS TO 2008 KIA Rondo TIRE PRESSURE MONITORING SYSTEM PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
