Auto Parts Search
2008 Saab 9-7X CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Saab REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Saab 9-7X car and truck
repair procedures including Saab engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Saab 9-7X automobile. Try the Automotix DIY solution today!
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Saab 9-7X AUTOMOBILES
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2008 Saab 9-7X Aero 6.0 V8 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 2008 Saab 9-7X DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Saab 9-7X AUTOMOBILES
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2008 Saab 9-7X 4.2I 4.2 L6 GAS
Refer to Figs. through for w...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Saab 9-7X TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2008 Saab 9-7X AUTOMOBILES
Starter, Replace
Vehicle: 2008 Saab 9-7X Aero 6.0 V8 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- Remove rear steering gear crossmember mounting bolts and crossmember.
- Remove wire harness from wire harness retaining clips on transmission oil cooler line bracket.
- Remove transmission oil cooler line bracket bolt.
- Remove right transmission cover bolt.
- Remove starter bolts.
- Move starter toward front of vehicle, and remove transmission cover.
- Remove starter solenoid heat shield.
- Tilt and rotate starter in order to pass starter between transmission oil cooler lines...
CLICK HERE TO GET FULL ACCESS TO 2008 Saab 9-7X STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Saab 9-7X AUTOMOBILES
Saab -> StabiliTrak Control System Warning Lamp -> 2006-09 9-7x
Vehicle: 2008 Saab 9-7X 5.3I 5.3 V8 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned on as a bulb check. If the StabiliTrak is switched off, the warning lamp will illuminate and the Driver Information System will display StabiliTrak off . When the ...
CLICK HERE TO GET FULL ACCESS TO 2008 Saab 9-7X MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2008 Saab 9-7X AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2008 Saab 9-7X 4.2I 4.2 L6 GAS
Inlet
- Drain coolant into a suitable container.
- Reposition inlet hose clamp at radiator and remove hose.
- Reposition inlet hose clamp at shut off valve and remove hose.
- Remove hose from vehicle.
- Reverse procedure to ...
CLICK HERE TO GET FULL ACCESS TO 2008 Saab 9-7X RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2008 Saab 9-7X AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2008 Saab 9-7X Aero 6.0 V8 GAS
- Remove air cleaner resonator outlet duct assembly by doing the following:
- Disconnect PVC valve, fresh air tube from air cleaner resonator outlet duct.
- Loosen clamps at MAF and IAT sensors.
- Remove bolt for air clean...
CLICK HERE TO GET FULL ACCESS TO 2008 Saab 9-7X SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2008 Saab 9-7X AUTOMOBILES
Component location diagrams for most 2008 Saab 9-7X cars and light trucks sold in the U.S. from 1990+.
 Doors Diagram for 2008 Saab 9-7X Aero 6.0 V8 GASComponents on diagram: |
 Engine Compartment Diagram for 2008 Saab 9-7X 5.3I 5.3 V8 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Saab 9-7X PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2008 Saab 9-7X AUTOMOBILES
OEM drawn wiring diagrams for most 2008 Saab 9-7X cars and light trucks sold in the U.S.
 2008 Saab 9-7X 5.3I 5.3 V8 GAS Wiring DiagramComponents on diagram: |
 2008 Saab 9-7X 5.3I 5.3 V8 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Saab 9-7X WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2008 Saab 9-7X AUTOMOBILES
OEM TSB listings for most 2008 Saab 9-7X cars and light trucks sold in the U.S. from 1985+.
|
Document: Engine Rattle Noise after R And R of the Crankshaft Balancer -Inspect Bolt Torque Vehicle: 2008 Saab 9-7X 4.2I 4.2 L6 GAS Symptoms: |
|
Document: GM of Canada New Vehicle Limited Warranty Tire Program Vehicle: 2008 Saab 9-7X 4.2I 4.2 L6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2008 Saab 9-7X TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2008 Saab 9-7X AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2008 Saab 9-7X cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2008 Saab 9-7X cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2008 Saab 9-7X cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2008 Saab 9-7X cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2008 Saab 9-7X SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2008 Saab 9-7X vehicle.
|
| Access the Complete guide! |
