Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Scion TC car and truck
repair procedures including Scion engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 Scion TC automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 Scion TC
- 2008 Scion TC 2.4 L4 GAS, CC:2398, Fuel Injection
- 2008 Scion TC Spec 2.4 L4 GAS, CC:2398, Fuel Injection
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing DTCs (Diagnostic Trouble Codes) -> Diagnostic Trouble Code Identification -> Reset Switch Test -> Using Scan Tool -> Using TPMS Warning Lamp
Vehicle: 2008 Scion TC 2.4 L4 GAS
Accessing Diagnostic Trouble Codes
Using TPMS Warning Lamp
- Place the ignition switch in the Off position.
- Using Toyota SST or other suitable jumper, connect terminals TC and CG of DLC3. The DLC3 is located under the left side of the instrument panel, Fig. .
- Place the ignition switch in the On position.
- Read and note DTCs indicated by flashes of the TPMS warning lamp, Fig. .
- If the TPMS warning lamp blinks in .25 second intervals, a normal condition is indicated, Fig. .
- If the TPMS warning lamp blinks in .5 second intervals followed by a 1.5 second pause, then additional .5 second i...
CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from mid 1990's+.
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2008 Scion TC 2.4 L4 GAS
Refer to Fig. for wiring...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from mid 1990's+.
Description
Vehicle: 2008 Scion TC Spec 2.4 L4 GAS
A tire pressure sensor and transmitter assembly is installed in each tire and wheel assembly, Fig. . The sensor measures the tire pressure. The measured tire pressure and transmitter identification are transmitted as radio waves to the TPMS (Tire Pressure Monitor System) warning antenna and receiver on the body. From the receiver the signal is sent to the TPMS ECU (Electronic Control Unit). If the transmitter identification has already been registered, the ECU will compares the measured air pressure value to the s...
CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> Reset Switch -> Tire Pressure Sensor -> TPMS ECU -> TPMS Receiver
Vehicle: 2008 Scion TC 2.4 L4 GAS
TPMS Receiver
Removal
- Disconnect the battery ground cable.
- Remove the right front door scuff plate.
- Remove the rear seat cushion assembly.
- Remove the rear seat back assembly.
- Remove the front door opening trim weather strip.
- Remove the front door side trim.
- Disconnect the tire pressure warning receiver electrical connector, then remove the attaching bolt and the receiver.
Installation
- Install the tire pressure warning receiver, then connect the electrical connector. Tighten the attaching bolt to 71 inch lbs.
- Install the right front door trim, the weather striping.
- Install the rear sea...
CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing DTCs (Diagnostic Trouble Codes) -> Diagnostic Trouble Code Identification -> Reset Switch Test -> Using Scan Tool -> Using TPMS Warning Lamp
Vehicle: 2008 Scion TC Spec 2.4 L4 GAS
Accessing Diagnostic Trouble Codes
Using TPMS Warning Lamp
- Place the ignition switch in the Off position.
- Using Toyota SST or other suitable jumper, connect terminals TC and CG of DLC3. The DLC3 is located under the left side of the instrument panel, Fig. .
- Place the ignition switch in the On position.
- Read and note DTCs indicated by flashes of the TPMS warning lamp, Fig. .
- If the TPMS warning lamp blinks in .25 second intervals, a normal condition is indicated, Fig. .
- If the TPMS warning lamp blinks in .5 second intervals followed by a 1.5 second pause, then additional .5 second i...
CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from mid 1990's+.
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2008 Scion TC Spec 2.4 L4 GAS
Refer to Fig. for wiring...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC TIRE PRESSURE MONITORING SYSTEM PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2008 Scion TC vehicle.
|
| Access the Complete guide! |
