Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Suzuki SX4 car and truck
repair procedures including Suzuki engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 Suzuki SX4 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 Suzuki SX4
- 2008 Suzuki SX4 Sport 2.0 L4 GAS, CC:1995, Fuel Injection
- 2008 Suzuki SX4 2.0 L4 GAS, CC:1995, Fuel Injection
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Suzuki SX4 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Suzuki SX4 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2008 Suzuki SX4 2.0 L4 GAS
- Raise and support vehicle.
- Before removing propeller shaft assembly, give place marks on joint flange and propeller shaft.
- Separate propeller shaft assembly from transfer output flange and rear...
CLICK HERE TO GET FULL ACCESS TO 2008 Suzuki SX4 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Suzuki SX4 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Suzuki SX4 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2008 Suzuki SX4 2.0 L4 GAS
Front
- Undo staking and remove drive shaft nut.
- Raise and support vehicle, then remove wheel.
- On 4WD models, drain transfer case oil into a suitable container.
- On all models, drain transaxle oil into a suitable container.
- Disconnect tie-rod end from steering knuckle using puller.
- Remove stabilizer joint.
- Remove brake hose mounting bolt.
- Remove wheel speed sensor and suspension control arm ball joint bolt.
- Disconnect front suspension control arm ball joint stud from steering knuckle.
- Using tire lever or plastic hammer, pull out drive shaft joint so as to release snap ring fitting of ...
CLICK HERE TO GET FULL ACCESS TO 2008 Suzuki SX4 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Suzuki SX4 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Suzuki SX4 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2008 Suzuki SX4 Sport 2.0 L4 GAS
Front
- Undo staking and remove drive shaft nut.
- Raise and support vehicle, then remove wheel.
- On 4WD models, drain transfer case oil into a suitable container.
- On all models, drain transaxle oil into a suitable container.
- Disconnect tie-rod end from steering knuckle using puller.
- Remove stabilizer joint.
- Remove brake hose mounting bolt.
- Remove wheel speed sensor and suspension control arm ball joint bolt.
- Disconnect front suspension control arm ball joint stud from steering knuckle.
- Using tire lever or plastic hammer, pull out drive shaft joint so as to release snap ring fitting of ...
CLICK HERE TO GET FULL ACCESS TO 2008 Suzuki SX4 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Suzuki SX4 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Suzuki SX4 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2008 Suzuki SX4 Sport 2.0 L4 GAS
- Raise and support vehicle.
- Before removing propeller shaft assembly, give place marks on joint flange and propeller shaft.
- Separate propeller shaft assembly from transfer output flange and rear...
CLICK HERE TO GET FULL ACCESS TO 2008 Suzuki SX4 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2008 Suzuki SX4 vehicle.
|
| Access the Complete guide! |
