Auto Parts Search
2009 Ford Mustang CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2009 Ford Mustang car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Ford Mustang automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2009 Ford Mustang AUTOMOBILES
Power Brake Units -> Adjustments -> Bendix System -> Single Diaphragm Booster
Vehicle: 2009 Ford Mustang 4.0 V6 GAS
Bendix System
- Disconnect master cylinder from booster leaving brake lines connected and secure cylinder aside.
- Start engine and operate engine at idle speed.
- With engine running, position gauge over pushrod. Gauge should bottom against booster housing with force of approximately five lbs. applied to pushrod, Fig. . Ensure pushrod is properly seated in booster when performing gauge inspection.
- If force required to seat gauge is more than five lbs., shorten length of pushrod.
- If force required to seat gauge is less than five lbs., lengthen pushrod.
- Install master cylinder and remove reservo...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Mustang BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Ford Mustang AUTOMOBILES
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2009 Ford Mustang Bullitt 4.6 V8 GAS
Disassemble
Do not, under any circumstance, clamp driveshaft assembly in jaws of a vise or similar holding fixture. Denting or localized fracturing may result, causing driveshaft failure during vehicle operation. Place driveshaft on a suitable workbench. Do not damage tube.
- Remove driveshaft.
- If components are not marked and therefore installed incorrectly, driveshaft imbalance can occur. Index-mark driveshaft components.
- Remove and discard all 4 of snap rings.
- Place a suitable tool in a vise.
- Position driveshaft slip yoke in a suitable tool.
- Press out a bearing cup. If nec...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Mustang DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Ford Mustang AUTOMOBILES
Description
Vehicle: 2009 Ford Mustang 4.0 V6 GAS
The Tire Pressure Monitoring (TPMS) system has the ability to monitor the air pressure of all five tires. The tire-mounted pressure sensors transmit signals to the TPMS module by using the valve stem as an antenna. These transmissions are sent approximately every 60 seconds when the vehicle speed exceeds 20 mph. T...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Mustang TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2009 Ford Mustang AUTOMOBILES
Alternator, Replace
Vehicle: 2009 Ford Mustang 4.0 V6 GAS
- Disconnect battery.
- Rotate Front End Accessory Drive (FEAD) belt tensioner counterclockwise and position FEAD belt aside.
- Disconnect alternator electrical connector.
- Position alternator B+ protective boot aside, remove nut and position alternator B+ terminal aside.
- Rem...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Mustang STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2009 Ford Mustang AUTOMOBILES
Cabin Air Filter Service -> Ford Motor Co. -> 2002-05 Thunderbird & 2005-09 Mustang
Vehicle: 2009 Ford Mustang Bullitt 4.6 V8 GAS
Under normal operating conditions the cabin air filter should be replaced every 15,000 miles. In dusty areas change the cabin air filter more often.
- Open the hood.
- Remove the lefthand and righthand cowl trim pieces.
- Note position of wiper blades on windshield.
- Remove the wiper arm nut covers, then the nuts and wiper arms.
- Remove the pin type retainers attaching the cowl cover to the cowl, Fig. .
- Release the righthand corner of the cabin air filter by pushing on the retaining cl...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Mustang CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Ford Mustang AUTOMOBILES
Ford Motor Co. Cars -> Check Fuel Cap Lamp ->
Vehicle: 2009 Ford Mustang 4.0 V6 GAS
The Check Fuel Cap Lamp will illuminate momentarily when the ignition switch is placed in the On position as a bulb check. If the lamp remains...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Mustang MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2009 Ford Mustang AUTOMOBILES
Radiator, Replace
Vehicle: 2009 Ford Mustang Shelby GT500 5.4 V8 GAS
- Drain cooling system into a suitable container.
- Remove seven bolts and lower splash shield.
- Remove six pushpin retainers and air deflector.
- Remove cooling fan motor and shroud.
- Disconnect degas bottle-to-radiator hose and position aside.
- Disconnect upper radiator hose from radiator and position aside.
- Disconnect lower radiator hose from radiator and position aside.
- Remove four bolts and radiator support brackets.
- Remove two power steering tubes and A/C condenser retaining nuts and position aside power steering tubes.
- Remove two A/C co...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Mustang RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2009 Ford Mustang AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2009 Ford Mustang Shelby GT500KR 5.4 V8 GAS
- Disconnect battery ground cable from battery.
- Rotate accessory drive belt tensioner counterclockwise to relieve t...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Mustang SERPENTINE BELT SERVICE PROCEDURES
TECHNICAL SERVICE BULLETINS FOR 2009 Ford Mustang AUTOMOBILES
OEM TSB listings for most 2009 Ford Mustang cars and light trucks sold in the U.S. from 1985+.
|
Document: SHELBY GT500 - CLUTCH DRAG - BUILT BEFORE 9/1/2008 Vehicle: 2009 Ford Mustang Shelby GT500 5.4 V8 GAS Symptoms: |
|
Document: Air Bag Warning Lamp On - DTC 2295 In Restraints Control Module Vehicle: 2009 Ford Mustang 4.0 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Mustang TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2009 Ford Mustang AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2009 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2009 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2009 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2009 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Mustang SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
