Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2009 KIA Optima car and truck
repair procedures including KIA engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2009 KIA Optima automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2009 KIA Optima
- 2009 KIA Optima LX 2.7 V6 GAS, CC:2656, Fuel Injection, Engine VIN:, Desg:4
- 2009 KIA Optima LX 2.4 L4 GAS, CC:2359, Fuel Injection, Engine VIN:, Desg:8
- 2009 KIA Optima EX 2.7 V6 GAS, CC:2656, Fuel Injection, Engine VIN:, Desg:4
- 2009 KIA Optima EX 2.4 L4 GAS, CC:2359, Fuel Injection, Engine VIN:, Desg:8
- 2009 KIA Optima SX 2.7 V6 GAS, CC:2656, Fuel Injection, Engine VIN:, Desg:4
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA Optima AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA Optima cars and light trucks sold in the U.S. from mid 1990's+.
Component Locations
Vehicle: 2009 KIA Optima LX 2.4 L4 GAS
Refer to F...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Optima TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA Optima AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA Optima cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> Tire Pressure Sensor -> TPMS Receiver
Vehicle: 2009 KIA Optima SX 2.7 V6 GAS
Tire Pressure Sensor
Removal
- Loosen the wheel lug nuts.
- Raise and support the vehicle with jack stands.
- Remove tire and wheel assembly from vehicle.
- Deflate air from tire assembly, then remove wheel weights.
- Break tire bead 180° from valve stem. When removing tire from rim caution should be taken not to hit valve stem with tire tools.
- Remove the valve nut, Fig. . Use caution when handling sensor.
- Discard valve nut.
Installation
- Use caution when handling sensor. Avoid getting any lubricant on sensor.
- Place valve in sensor and turn valve three times with square part of screw in slot. T...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Optima TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA Optima AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA Optima cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures -> Tire Pressure Sensor Initiation -> TPMS Receiver
Vehicle: 2009 KIA Optima EX 2.7 V6 GAS
Tire Pressure Sensor Initiation
- Using Kia TPMS exciter tool, or equivalent, read the four tire pressure sensor IDs starting with sensor 1 the LH front wheel.
- Read the remaining sensors in the following order:
- Sensor 2, RH front wheel.
- Sensor 3, LH rear wheel.
- Sensor 4, RH rear wheel.
- Connect the Kia exciter tool, or equivalent, to the DLC (Data Link Connector) located under the LH side of the instrument panel.
- Using the tool, register the four sensor IDs to the TPMS receiver.
- Disconnect the tool from the DLC.
- Place the ignition switch in the Off position for 4 minutes, then turn the i...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Optima TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA Optima AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA Optima cars and light trucks sold in the U.S. from mid 1990's+.
Reset Procedures
Vehicle: 2009 KIA Optima LX 2.7 V6 GAS
The Low Tire Pressure Warning lamp will illuminate for approximately three seconds as a bulb check when the ignition switch is placed in the On position. This system uses radio frequency pressure sensors which mon...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Optima TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA Optima AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA Optima cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures -> Tire Pressure Sensor Initiation -> TPMS Receiver
Vehicle: 2009 KIA Optima LX 2.4 L4 GAS
Tire Pressure Sensor Initiation
- Using Kia TPMS exciter tool, or equivalent, read the four tire pressure sensor IDs starting with sensor 1 the LH front wheel.
- Read the remaining sensors in the following order:
- Sensor 2, RH front wheel.
- Sensor 3, LH rear wheel.
- Sensor 4, RH rear wheel.
- Connect the Kia exciter tool, or equivalent, to the DLC (Data Link Connector) located under the LH side of the instrument panel.
- Using the tool, register the four sensor IDs to the TPMS receiver.
- Disconnect the tool from the DLC.
- Place the ignition switch in the Off position for 4 minutes, then turn the i...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Optima TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA Optima AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA Optima cars and light trucks sold in the U.S. from mid 1990's+.
Description
Vehicle: 2009 KIA Optima EX 2.7 V6 GAS
The TPMS (Tire Pressure Monitor System) alerts the driver when a large change in the pressure of one tire exists. The system detects a tire pres...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Optima TIRE PRESSURE MONITORING SYSTEM PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2009 KIA Optima vehicle.
|
| Access the Complete guide! |
