Auto Parts Search
2009 Mazda 3 CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Mazda REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Mazda 3 AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2009 Mazda 3 I 2.0 L4 GAS
Performing the following procedures without first removing the ABS wheel-speed sensor may possibly cause an open circuit in the wiring harness if pulled by mistake. Before performing the following procedures, disconnect the ABS wheel speed sensor connector (axle side) and fix the wiring harness to an appropriate place where it will not be pulled by mistake while servicing vehicle.
Note: When replacing the driveshaft (double offset joint type), replace it as a single unit because it cannot be disassembled.
- Raise and support vehicle and support it with safety stands in proper...
CLICK HERE TO GET FULL ACCESS TO 2009 Mazda 3 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Mazda 3 AUTOMOBILES
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Identification -> Intermittent & Poor Connections -> Intermittents -> Malfunctioning Wheel Unit Identification -> Poor Connections
Vehicle: 2009 Mazda 3 Mazdaspeed 2.3 L4 GAS
Accessing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to Data Link Connector (DLC) and follow manufacturer's instructions.
Diagnostic Trouble Code Identification
[[table data]]Clearing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to Data Link Connector (DLC), and follow manufacturer's instructions.
Malfunctioning Wheel Unit Identification
The tire pressure monitoring system (TPMS) does not identify the location of the failed wheel unit on the vehicle (LF, RF, LR, RR). The TPMS identifies each wheel unit as No.1, No.2, No.3 and No.4. In order to identify ...
CLICK HERE TO GET FULL ACCESS TO 2009 Mazda 3 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2009 Mazda 3 AUTOMOBILES
Starter, Replace
Vehicle: 2009 Mazda 3 I 2.0 L4 GAS
- Unhook battery cover from battery box.
- Disconnect battery ground cable.
- Raise vehicle on lift.
- Remove under cover bolts then remove undercover.
- On models equipped with manual transaxle, remove clutch release cylinder with pipe still connected.
- On all models, remove starter motor wiring harness bracket nuts then remove bracket.
- Remove nut f...
CLICK HERE TO GET FULL ACCESS TO 2009 Mazda 3 STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2009 Mazda 3 AUTOMOBILES
Cabin Air Filter Service -> Mazda -> Mazda3
Vehicle: 2009 Mazda 3 I 2.0 L4 GAS
Under normal operating conditions the cabin air filter should be replaced every 24 months or 25,000 miles. In dusty areas change the cabin air filter more often.
- Disconnect the battery ground cable.
- Remove the passenger side instrument panel junction block cover.
- For junction block electrical connectors with release tabs, press the tabs inward and disconnect the connector.
- For junction block electrical connectors with levers, move the lever upward to the release position and disconnect the connector.
- Turn the junction block screws counterclockwise. The screws cannot be removed from the juncti...
CLICK HERE TO GET FULL ACCESS TO 2009 Mazda 3 CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Mazda 3 AUTOMOBILES
Mazda -> Low Coolant Lamp ->
Vehicle: 2009 Mazda 3 S 2.3 L4 GAS
This lamp should light when engine coolant level in the radiator drops below a predetermined le...
CLICK HERE TO GET FULL ACCESS TO 2009 Mazda 3 MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2009 Mazda 3 AUTOMOBILES
Heater Hose, Replace -> Bypass -> Inlet -> Outlet
Vehicle: 2009 Mazda 3 S 2.3 L4 GAS
Inlet
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at heater core.
- Remove hose from heater core.
- Reposition hose clamp at heater pipe.
- Remove hose from heater pipe.
- Remove hose from vehicle.
- Reverse procedure to install.
Outlet
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at he...
CLICK HERE TO GET FULL ACCESS TO 2009 Mazda 3 RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2009 Mazda 3 AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2009 Mazda 3 I 2.0 L4 GAS
- Rotate or lift the belt tensioner arm, using a suitable tool to relieve tension from dr...
CLICK HERE TO GET FULL ACCESS TO 2009 Mazda 3 SERPENTINE BELT SERVICE PROCEDURES
TECHNICAL SERVICE BULLETINS FOR 2009 Mazda 3 AUTOMOBILES
OEM TSB listings for most 2009 Mazda 3 cars and light trucks sold in the U.S. from 1985+.
Document: SERVICE POINTS FOR ENGINE REPLACEMENT DUE TO ENGINE NOISE Vehicle: 2009 Mazda 3 I 2.0 L4 GAS Symptoms: |
Document: A/C STOPS COOLING/REDUCED AIRFLOW DURING A LONG DRIVE IN HUMID TEMPERATURES Vehicle: 2009 Mazda 3 I 2.0 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2009 Mazda 3 TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2009 Mazda 3 AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2009 Mazda 3 cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2009 Mazda 3 cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2009 Mazda 3 cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2009 Mazda 3 cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2009 Mazda 3 SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2009 Mazda 3 vehicle. |
Access the Complete guide! |