Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2009 Subaru Outback car and truck
repair procedures including Subaru engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2009 Subaru Outback automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2009 Subaru Outback
- 2009 Subaru Outback 2.5I 2.5 H4 GAS, CC:2458, Fuel Injection
- 2009 Subaru Outback XT Limited 2.5 H4 GAS, CC:2458, Fuel Injection
- 2009 Subaru Outback 2.5I Limited 2.5 H4 GAS, CC:2458, Fuel Injection
- 2009 Subaru Outback 3.0 R Limited 3.0 H6 GAS, CC:3000, Fuel Injection
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Subaru Outback AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 Subaru Outback cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures -> Transmitter ID Registration
Vehicle: 2009 Subaru Outback XT Limited 2.5 H4 GAS
Transmitter ID Registration
The following procedure must be performed when tire pressure sensor or TPMS control module is replaced. If tire pressure sensor transmitter ID cannot be registered after two attempts, replace the TPMS control module. If the registration procedure is not performed for 5 minutes or more or if the ignition switch is placed in the Off position, the registration mode will be cancelled.
- Check and adjust all tires to the recommended pressure.
- Connect the Subaru Select Monitor tool, or equivalent tool, then select Each System Check, Tire Pressure Monitor and ...
CLICK HERE TO GET FULL ACCESS TO 2009 Subaru Outback TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Subaru Outback AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 Subaru Outback cars and light trucks sold in the U.S. from mid 1990's+.
Reset Procedures
Vehicle: 2009 Subaru Outback 3.0 R Limited 3.0 H6 GAS
This warning lamp will illuminate when tire pressure falls below a specified psi. When the warning lamp illuminates, check the air pressu...
CLICK HERE TO GET FULL ACCESS TO 2009 Subaru Outback TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Subaru Outback AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 Subaru Outback cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> Snap In Type -> Tire Pressure Sensor -> TPMS Control Module
Vehicle: 2009 Subaru Outback 2.5I Limited 2.5 H4 GAS
Tire Pressure Sensor
Snap In Type
Removal
- Loosen the lug nuts.
- Raise and support vehicle with jack stands, then remove the wheel and tire assembly.
- Release the air pressure from the tire.
- Using a suitable tire changer, remove the tire from the wheel.
- Remove the screw attaching the tire pressure sensor to the valve stem, Fig. .
- Remove the valve stem.
Installation
Use a valve and screw when installing the tire pressure sensor.
- Use a valve and screw when installing the tire pressure sensor. Tighten the screw to 12 inch lbs., Fig. .
- Install the pressure sensor and valve stem by aligning w...
CLICK HERE TO GET FULL ACCESS TO 2009 Subaru Outback TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Subaru Outback AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 Subaru Outback cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures -> Transmitter ID Registration
Vehicle: 2009 Subaru Outback 2.5I 2.5 H4 GAS
Transmitter ID Registration
The following procedure must be performed when tire pressure sensor or TPMS control module is replaced. If tire pressure sensor transmitter ID cannot be registered after two attempts, replace the TPMS control module. If the registration procedure is not performed for 5 minutes or more or if the ignition switch is placed in the Off position, the registration mode will be cancelled.
- Check and adjust all tires to the recommended pressure.
- Connect the Subaru Select Monitor tool, or equivalent tool, then select Each System Check, Tire Pressure Monitor and ...
CLICK HERE TO GET FULL ACCESS TO 2009 Subaru Outback TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Subaru Outback AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 Subaru Outback cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> Snap In Type -> Tire Pressure Sensor -> TPMS Control Module
Vehicle: 2009 Subaru Outback 3.0 R Limited 3.0 H6 GAS
Tire Pressure Sensor
Snap In Type
Removal
- Loosen the lug nuts.
- Raise and support vehicle with jack stands, then remove the wheel and tire assembly.
- Release the air pressure from the tire.
- Using a suitable tire changer, remove the tire from the wheel.
- Remove the screw attaching the tire pressure sensor to the valve stem, Fig. .
- Remove the valve stem.
Installation
Use a valve and screw when installing the tire pressure sensor.
- Use a valve and screw when installing the tire pressure sensor. Tighten the screw to 12 inch lbs., Fig. .
- Install the pressure sensor and valve stem by aligning w...
CLICK HERE TO GET FULL ACCESS TO 2009 Subaru Outback TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Subaru Outback AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 Subaru Outback cars and light trucks sold in the U.S. from mid 1990's+.
Description
Vehicle: 2009 Subaru Outback 3.0 R Limited 3.0 H6 GAS
The TPMS (Tire Pressure Monitor System) alerts the driver when a large change in the pressure of one tire exists. The system detects a tire pres...
CLICK HERE TO GET FULL ACCESS TO 2009 Subaru Outback TIRE PRESSURE MONITORING SYSTEM PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2009 Subaru Outback vehicle.
|
| Access the Complete guide! |
