Auto Parts Search
Dodge Nitro CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Dodge REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Year
2010 | 2009 | 2008 | 2007 |

BRAKE SERVICE PROCEDURES FOR Dodge Nitro AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported Dodge Nitro cars and light trucks from 1990+.
Disc Brakes -> Troubleshooting -> Brake Chatter -> Brake Drag -> Brake Fade -> Brake Pull -> Brake Squeal Or Squeak -> Hard Pedal Or High Pedal Effort -> Low Pedal -> Pedal Falls Away -> Pedal Pulsation -> Rear Brake Grab Or Pull -> Spongy Pedal
Vehicle: 2007 Dodge Nitro SLT 3.7 V6 GAS
Pedal Falls Away
- System leak at brake line, fitting, hose or caliper/wheel cylinder.
- Internal leakage in master cylinder caused by worn or damaged piston cups.
- Internal leak in ABS or RWAL system.
Low Pedal
- Worn brake linings.
- Worn drums or rotors.
- Rear brakes out of adjustment.
Spongy Pedal
- Air in hydraulic system.
- Thin brake drums.
- Substandard brake lines and hoses.
Hard Pedal Or High Pedal Effort
- Linings that are water soaked, contaminated or glazed.
- Faulty power booster or check valve.
Pedal Pulsation
- Disc brake rotors have excessive lateral runout or thickness variation.
- Out of round brake ...
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR Dodge Nitro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported Dodge Nitro cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> U-Joint with Injected Rings -> U-Joint with Snap Rings
Vehicle: 2008 Dodge Nitro SXT 3.7 V6 GAS
This procedure describes a propeller shaft equipped with a cardan joint in the tube yoke. For propeller shafts equipped with a companion/slip yoke, repeat the steps to remove the remaining cardan joint.
U-Joint with Snap Rings
Disassemble
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke.
- Position yoke with grease fitting if equipped, pointing up.
- Position a socket with a inside diameter large enough to receive bearing cap, beneath yoke on a press.
- Place another socket with an outside diameter smaller than bearing cap on ...
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR Dodge Nitro AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported Dodge Nitro cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Identification -> Intermittent & Poor Connections -> Intermittents -> Poor Connections -> Tire Pressure Sensor Check
Vehicle: 2008 Dodge Nitro R/T 4.0 V6 GAS
Accessing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to DLC (Data Link Connector) and follow manufacturer's instructions.
Diagnostic Trouble Code Identification
Refer to Fig. for diagnostic trouble code identification.
Clearing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to DLC (Data Link Connector), and follow manufacturer's instructions.
Intermittent & Poor Connections
Intermittents
Most intermittents are caused by faulty electrical connections or wiring. Inspect for the following:
- Wiring broken inside insulation.
- Poor connection between m...
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR Dodge Nitro AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported Dodge Nitro cars and light trucks from 1990+.
Starter, Replace
Vehicle: 2008 Dodge Nitro SLT 3.7 V6 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- On models equipped with 4WD, remove front propeller shaft.
- On all models, remove heat shield bolts and starter heat shield.
- Remove solenoid nut from mounting stud.
- Pull battery cable from mounting stud while removing electrical connector from solenoid terminal.
- Remove starter mounting bolts.
- Remove starter...
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR Dodge Nitro AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported Dodge Nitro cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> All Wheel Drive (AWD) Warning Lamp ->
Vehicle: 2009 Dodge Nitro R/T 4.0 V6 GAS
This light monitors the AWD system. The light will turn on for a bulb check when the ignition switch is turned to the on position and may stay on for as long as three seconds. When the lamp is illuminated solid here is an A...
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR Dodge Nitro AUTOMOBILES
Includes radiator, cooling and heater hose replacement procedures for domestic and imported Dodge Nitro cars and light trucks from 1990+
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2007 Dodge Nitro SXT 3.7 V6 GAS
Lower
- Raise and support vehicle.
- Drain cooling system into a suitable container.
- Reposition hose clamp from radiator.
- Remove radiator outlet hose from radiator.
- Reposition hose clamp from water pump.
- Remove radiator outlet hose from water pump and from vehicle.
- Reverse pr...
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR Dodge Nitro AUTOMOBILES
Serpentine belt replacement procedures with corresponding images for most domestic and imported Dodge Nitro cars and light trucks sold in the U.S. from 1990+.
Serpentine Drive Belt, Replace
Vehicle: 2007 Dodge Nitro SXT 3.7 V6 GAS
- Disconnect battery ground cable.
- Remove combination washer reservoir/coolant recovery container and move aside.
- Rotate belt tensioner until it contacts stop.
- Remove drive belt.
- Carefully return tens...
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR Dodge Nitro AUTOMOBILES
Component location diagrams for most Dodge Nitro cars and light trucks sold in the U.S. from 1990+.
![]() Components on diagram: |
![]() Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR Dodge Nitro AUTOMOBILES
OEM drawn wiring diagrams for most Dodge Nitro cars and light trucks sold in the U.S.
![]() Components on diagram: |
![]() Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR Dodge Nitro AUTOMOBILES
OEM TSB listings for most Dodge Nitro cars and light trucks sold in the U.S. from 1985+.
Document: In Cold Climates A MIL Illumination P0123 Or P0222 Or Stored Diagnostic Trouble Code P0123 Or P0222 And The ETC Light Illuminated Vehicle: 2009 Dodge Nitro SLT 3.7 V6 GAS Auto Systems: |
Document: TIRE PRESSURE MONITORING SYSTEM DISPLAYS DASHES "--" WHEN SPARE TIRE IS USED - REVISED Vehicle: 2007 Dodge Nitro SLT 3.7 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR Dodge Nitro AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most Dodge Nitro cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most Dodge Nitro cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most Dodge Nitro cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most Dodge Nitro cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO Dodge Nitro SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
![]() |
Access the Complete guide! |