Auto Parts Search
1990 Acura Integra CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Acura REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1990 Acura Integra car and truck
repair procedures including Acura engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Acura Integra automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR 1990 Acura Integra AUTOMOBILES
A/C & Cooling System Maintenance -> Acura -> Legend, Vigor & 1990-95 Integra & NSX
Vehicle: 1990 Acura Integra LS 1.8 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Acura Integra AUTOMOBILES
ACURA, DISC BRAKES -> BRAKE PADS -> FRONT -> REAR
Vehicle: 1990 Acura Integra LS 1.8 L4 GAS
FRONT
- Raise and support front of vehicle and remove wheels.
- Remove caliper pin bolt, then pivot caliper up away from pads.
- Remove brake pad shims and the pads, Figs. through .
- Clean caliper and inspect for excessive wear or damage.
- Install pad retainers, then the pad shims and pads, Figs. through .
- Back out bleed screw and push in piston to allow caliper to fit over pads, then tighten bleed screw.
- Pivot caliper into position, then install pin bolt and torque to specifications.
REAR
- Raise and support rear of vehicle and remove wheels.
- Remove caliper shield, if equipped, then discon...
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1990 Acura Integra AUTOMOBILES
Acura -> Fuel Filter Replacement -> Integra, Legend, NSX, Vigor, 2.5TL, 3.0CL & 3.5RL -> Fuel System Pressure Relief -> Removal & Installation
Vehicle: 1990 Acura Integra RS 1.8 L4 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental fuel spray.
After the battery has been disconnected and reconnected, some abnormal driveability symptoms may occur. The vehicle may need to be driven 10 miles or more to relearn its adaptive strategy.
Fuel System Pressure Relief
- Obtain the vehicle owner's radio ...
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Acura Integra AUTOMOBILES
CV AXLE SHAFT, Replace -> Driveshaft -> Intermediate shaft
Vehicle: 1990 Acura Integra GS 1.8 L4 GAS
Driveshaft
- Raise and support front of vehicle.
- Remove front wheel, then drain transaxle fluid into a suitable container. If removing left driveshaft only, it is not necessary to drain transaxle.
- Raise spindle nut lock tab and remove nut.
- Remove damper fork bolt and pinch bolt, then damper fork.
- Remove steering knuckle to lower control arm castellated nut cotter pin and nut.
- Separate lower control arm from steering knuckle using a suitable puller.
- Pull steering knuckle outward and tap driveshaft outboard joint from steering knuckle.
- Pry driveshaft out with a screwdriver to force s...
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1990 Acura Integra AUTOMOBILES
Alternator, Replace
Vehicle: 1990 Acura Integra GS 1.8 L4 GAS
- Remove left driveshaft.
- Disconnect battery ground cable at battery.
- Disconnect alternator connector from alternator.
- Remove terminal nut and WHT wire from B terminal.
- Remove three mounting bracket bolts and mounting bracket.
- Remove adjusting nut and upper mounting bolt, then pull out alternator.
- Loosen adjusting nut, then remove mounting nut.
- Remove alternator belt from alternator pulley.
- Remov...
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Acura Integra AUTOMOBILES
Acura -> Side Air Bag off Lamp ->
Vehicle: 1990 Acura Integra RS 1.8 L4 GAS
This indicator should light for a few seconds when the ignition switch placed in the on position and then go Off. The lamp is used a an alert that the passenger side air bag has been automatically shut off. The passenger side air bag w...
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1990 Acura Integra AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 1990 Acura Integra LS 1.8 L4 GAS
Lower
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at radiator outlet.
- Remove hose from radiator.
- Reposition hose clamp at water inlet.
- Remove hose from water inlet.
- Remove hose from vehicle.
- Reverse procedure to inst...
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1990 Acura Integra AUTOMOBILES
Serpentine Drive Belt, Replace -> Air Conditioning -> Alternator -> Power Steering
Vehicle: 1990 Acura Integra RS 1.8 L4 GAS
Alternator
- Disconnect battery ground cable from battery.
- Loosen upper mounting nut.
- Loosen lower mounting bolt and adjustment locknut.
- Remove A/C compressor drive and alternator drive belt.
- Clean and inspect belt surfaces of all pulleys.
- Reverse procedure to install, noting the following:
- Torque upper alternator adjusting nut to 17 ft. lbs.
- Torque lower alternator adjusting nut to 33 ft. lbs.
Air Conditioning
- Disconnect battery ground cable from battery.
- Loosen adjust pulley bracket pivot bolt and adjusting bolt.
- Remove A/C compressor drive belt from pulleys.
- On models equippe...
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1990 Acura Integra AUTOMOBILES
Component location diagrams for most 1990 Acura Integra cars and light trucks sold in the U.S. from 1990+.
 LH Door Connector Locations Diagram for 1990 Acura Integra RS 1.8 L4 GASComponents on diagram: |
 Heater Recirculation Control Motor Location Diagram for 1990 Acura Integra LS 1.8 L4 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1990 Acura Integra AUTOMOBILES
OEM drawn wiring diagrams for most 1990 Acura Integra cars and light trucks sold in the U.S.
 1990 Acura Integra GS 1.8 L4 GAS Wiring DiagramComponents on diagram: |
 1990 Acura Integra LS 1.8 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1990 Acura Integra AUTOMOBILES
OEM TSB listings for most 1990 Acura Integra cars and light trucks sold in the U.S. from 1985+.
|
Document: Battery Testing and Replacement Vehicle: 1990 Acura Integra LS 1.8 L4 GAS Auto Systems: |
|
Document: Battery Testing and Replacement Vehicle: 1990 Acura Integra LS 1.8 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1990 Acura Integra AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1990 Acura Integra cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1990 Acura Integra cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1990 Acura Integra cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1990 Acura Integra cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1990 Acura Integra SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1990 Acura Integra vehicle.
|
| Access the Complete guide! |
