Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1990 Chevrolet Corvette car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1990 Chevrolet Corvette automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1990 Chevrolet Corvette
- 1990 Chevrolet Corvette 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:8
- 1990 Chevrolet Corvette ZR-1 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:J
BRAKE SERVICE PROCEDURES FOR 1990 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Chevrolet Corvette cars and light trucks from 1990+.
DISC BRAKES, GENERAL MOTORS -> PBR Dual Piston Caliper -> SERVICE -> BRAKE SHOE & LINING INSTALLATION -> BRAKE SHOE & LINING REMOVAL -> CALIPER ASSEMBLY -> CALIPER DISASSEMBLY -> CALIPER INSTALLATION -> CALIPER REMOVAL
Vehicle: 1990 Chevrolet Corvette ZR-1 5.7 V8 GAS
CALIPER REMOVAL
- Remove2/3 of the total brake fluid capacity from master cylinder reservoir.
- Raise and support vehicle, then remove tire and wheel assembly.
- Install two wheel retaining nuts to retain rotor in position.
- If caliper requires overhaul, remove inlet fitting attaching bolt, then disconnect inlet fitting from caliper housing. Discard the two gaskets, then plug openings in inlet fitting and caliper to prevent loss or contamination of fluid. Do not crimp brake hose, as this may damage internal structure of hose.
- Remove circlip (11) and retaining pin (7), Fig. , then pull caliper off r...
CLICK HERE TO GET FULL ACCESS TO 1990 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Chevrolet Corvette cars and light trucks from 1990+.
DISC BRAKES, GENERAL MOTORS -> PBR Dual Piston Caliper -> DESCRIPTION
Vehicle: 1990 Chevrolet Corvette 5.7 V8 GAS
This front caliper, Fig. , consists of dual pistons and an aluminum housing which is suspended on the shoe and lining assemblies. Hydraulic pressure, created by applying force to the brake pedal, acts equally against the pistons and the botto...
CLICK HERE TO GET FULL ACCESS TO 1990 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Chevrolet Corvette cars and light trucks from 1990+.
DISC BRAKES, GENERAL MOTORS -> PBR Single Piston Caliper -> DESCRIPTION
Vehicle: 1990 Chevrolet Corvette 5.7 V8 GAS
This rear caliper, Fig. , consists of a single piston and an aluminum housing which is suspended in a mounting bracket through two slide pins. Hydraulic pressure, created by applying force to the brake pedal, acts equally against the piston and the bottom of the caliper bore to move the piston outward. This action slides the caliper inward, resulting in a clamping action on the brake rotor. This clamping act...
CLICK HERE TO GET FULL ACCESS TO 1990 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Chevrolet Corvette cars and light trucks from 1990+.
HYDRAULIC BRAKE SYSTEM, GENERAL MOTORS -> TROUBLESHOOTING -> CHECKING FOR FLUID LEAKAGE -> ROAD TESTING
Vehicle: 1990 Chevrolet Corvette 5.7 V8 GAS
When troubleshooting the hydraulic brake system, perform the following checks and inspections as outlined below. If problem still exists within system, refer toFig. first, then toFig. as necessary.
ROAD TESTING
When testing brakes, ensure the road is level and dry. Test brakes at both light and heavy pedal pressure. Do not lock up brakes or slide tires during a brake test.
Check the tires on the vehicle before performing a brake test. Tires should be equally inflated, identical in size ...
CLICK HERE TO GET FULL ACCESS TO 1990 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Chevrolet Corvette cars and light trucks from 1990+.
ANTI-LOCK BRAKES, GENERAL MOTORS -> Corvette (Bosch ABS II Type) -> OPERATION
Vehicle: 1990 Chevrolet Corvette ZR-1 5.7 V8 GAS
When ignition switch is turned to On position, amber ANTI-LOCK warning lamp in the instrument panel illuminates. When engine is started, it goes out. If ABS warning light does not go out or comes on permanently while driving, it indicates a fault in ABS system.
When starting vehicle, the control module performs a functional check of electrical circuitry. The test cycle checks components of the monitoring circuit as well as the logic section. Test sample signals are sent to the control module, which checks whether or not the correct output signals are available.
Since the ABS system may ...
CLICK HERE TO GET FULL ACCESS TO 1990 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Chevrolet Corvette cars and light trucks from 1990+.
DISC BRAKES, GENERAL MOTORS -> General Information -> INSPECTION OF CALIPER
Vehicle: 1990 Chevrolet Corvette ZR-1 5.7 V8 GAS
Should it become necessary to remove the caliper for installation of new parts, clean all parts in alcohol, wipe dry using lint free cloths, using an air hose to blow out drilled passages and bores. Check dust boots for punctures or tears. If punctures or tears are evident, new boots should be installed upon reassembly.
Inspect piston bores for scoring or pitting. Bores that show light scratches or corrosion can usually be cleaned with crocus cloth. However, bores that have deep scratches or scoring may be honed, provided the diameter of the...
CLICK HERE TO GET FULL ACCESS TO 1990 Chevrolet Corvette BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
