Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1990 Chevrolet Corvette car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1990 Chevrolet Corvette automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1990 Chevrolet Corvette
- 1990 Chevrolet Corvette 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:8
- 1990 Chevrolet Corvette ZR-1 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:J
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1990 Chevrolet Corvette AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported 1990 Chevrolet Corvette cars and light trucks from 1990+.
Starter, Replace
Vehicle: 1990 Chevrolet Corvette ZR-1 5.7 V8 GAS
If shims are required between starter and engine block, they should be placed in their original location during installation. If starter is noisy during cranking, remove one .015 inch double shim or add one .015 single shim to outer bolt. If starter makes a high pitched whine after firing, add .015 inch double shims until noise ceases.
- Disconnect battery ground cable.
- Drain cooling system into a suita...
CLICK HERE TO GET FULL ACCESS TO 1990 Chevrolet Corvette STARTER & ALTERNATOR REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1990 Chevrolet Corvette AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported 1990 Chevrolet Corvette cars and light trucks from 1990+.
Alternator, Replace
Vehicle: 1990 Chevrolet Corvette 5.7 V8 GAS
- Disconnect battery ground cable, then remove intake air duct.
- Remove throttle body extension.
- Using a suitable 1/2 inch breaker bar, rotate serpentine drive belt tensioner to release belt tension.
- Remove serpentine drive belt from water pump pulley, then remove belt.
- Remove alternator lower support bolts and bracket, Fig. .
- Remove rear support bracket to alternator retaining bolt.
- Remove alternator upper suppor...
CLICK HERE TO GET FULL ACCESS TO 1990 Chevrolet Corvette STARTER & ALTERNATOR REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1990 Chevrolet Corvette AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported 1990 Chevrolet Corvette cars and light trucks from 1990+.
Starter, Replace
Vehicle: 1990 Chevrolet Corvette 5.7 V8 GAS
If shims are required between starter and engine block, they should be placed in their original location during installation. If starter is noisy during cranking, remove one .015 inch double shim or add one .015 single shim to outer bolt. If starter makes a high pitched whine after firing, add .015 inch double shims until noise ceases.
- Disconnect battery ground cable.
- Drain cooling system into a suita...
CLICK HERE TO GET FULL ACCESS TO 1990 Chevrolet Corvette STARTER & ALTERNATOR REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1990 Chevrolet Corvette AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported 1990 Chevrolet Corvette cars and light trucks from 1990+.
Alternator, Replace
Vehicle: 1990 Chevrolet Corvette ZR-1 5.7 V8 GAS
- Disconnect battery ground cable, then remove intake air duct.
- Remove throttle body extension.
- Using a suitable 1/2 inch breaker bar, rotate serpentine drive belt tensioner to release belt tension.
- Remove serpentine drive belt from water pump pulley, then remove belt.
- Remove alternator lower support bolts and bracket, Fig. .
- Remove rear support bracket to alternator retaining bolt.
- Remove alternator upper suppor...
CLICK HERE TO GET FULL ACCESS TO 1990 Chevrolet Corvette STARTER & ALTERNATOR REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
