Auto Parts Search
We have info for following modifications of 1990 Ford F-250 Pickup
- 1990 Ford F-250 Pickup 5.0 V8 GAS, CID:302, Fuel Injection, Aspiration:302, Engine VIN:, Desg:N
- 1990 Ford F-250 Pickup 4.9 L6 GAS, CID:300, Fuel Injection, Aspiration:300, Engine VIN:, Desg:Y
- 1990 Ford F-250 Pickup 5.8 V8 GAS, CID:351, Fuel Injection, Aspiration:351, Engine VIN:, Desg:H
- 1990 Ford F-250 Pickup 7.3 V8 DIESEL, CID:445, Fuel Injection, Aspiration:445, Engine VIN:, Desg:M
- 1990 Ford F-250 Pickup 7.5 V8 GAS, CID:460, Fuel Injection, Aspiration:460, Engine VIN:, Desg:G
- 1990 Ford F-250 Pickup Super CAB 4.9 L6 GAS, CID:300, Fuel Injection, Aspiration:300, Engine VIN:, Desg:Y
- 1990 Ford F-250 Pickup Super CAB 5.8 V8 GAS, CID:351, Fuel Injection, Aspiration:351, Engine VIN:, Desg:H
- 1990 Ford F-250 Pickup Super CAB 7.3 V8 DIESEL, CID:445, Fuel Injection, Aspiration:445, Engine VIN:, Desg:M
- 1990 Ford F-250 Pickup Super CAB 7.5 V8 GAS, CID:460, Fuel Injection, Aspiration:460, Engine VIN:, Desg:G
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford F-250 Pickup AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford F-250 Pickup cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Fuel Cap Lamp ->
Vehicle: 1990 Ford F-250 Pickup Super CAB 5.8 V8 GAS
The Check Fuel Cap Lamp will illuminate momentarily when the ignition switch is placed in the On position as a bulb check. If the lamp remains...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford F-250 Pickup MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford F-250 Pickup AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford F-250 Pickup cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Engine Lamp -> 1990-91 EEC-IV
Vehicle: 1990 Ford F-250 Pickup 7.5 V8 GAS
This lamp will light when the ignition is turned On. After engine is started the lamp should go off, unless a problem has been detected by the EEC-IV system. After diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored codes are cleared from EEC-IV system memory. After diagnosis and repair, EEC-IV memory may be cleared of stored codes as follows:
- With ignition turned Off, connect a jumper wire between Self Test and Self Test Input (STI) connectors.
- On Aerostar, the Self Test and STI connectors are gray in color and are located on lefthand fender apron...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford F-250 Pickup MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford F-250 Pickup AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford F-250 Pickup cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Anti-Lock Or Rear Anti-Lock Brake System Warning ->
Vehicle: 1990 Ford F-250 Pickup 7.5 V8 GAS
Red and yellow indicator lamps are used to warn of system faults. The red lamp warns of such faults as low brake fluid level, parking brake On, system pressure differential and other system faults. The red indicator lamp will light for approximately two seconds during engine starting and should go off, unless parking brake is applied or a problem in the brake system exist. The red indicator lamp should reset after repairs to system have ...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford F-250 Pickup MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford F-250 Pickup AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford F-250 Pickup cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Emission Maintenance Reminder Indicator ->
Vehicle: 1990 Ford F-250 Pickup 5.8 V8 GAS
This lamp should light after approximately 60,000 miles of operation, Fig. . The amber lens lamp is located on the instrument panel and has the word Emissions, Emiss or EGR printed on it. After performing the required emission control maintenance, the module must be replaced or reset, depending on type of module used. On module equipped with reset feature, reset the module as follows:
- Turn ignition Off.
- On Aerostar models, the module is located under the instrument panel near the bulkhead connector.
- On Bronco, Explorer and F-Series, the module is attached to the instrument cluster to the left of ...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford F-250 Pickup MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford F-250 Pickup AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford F-250 Pickup cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Rear Load Leveling (CHECK SUSP) ->
Vehicle: 1990 Ford F-250 Pickup Super CAB 7.5 V8 GAS
The CHECK SUSP indicator lights when there is a fault of the rear load ...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford F-250 Pickup MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford F-250 Pickup AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford F-250 Pickup cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Low Coolant Lamp ->
Vehicle: 1990 Ford F-250 Pickup 5.8 V8 GAS
This lamp should light when engine coolant level in the radiator drops below a predetermined le...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford F-250 Pickup MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1990 Ford F-250 Pickup vehicle. |
Access the Complete guide! |