Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1992 Ford Probe car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1992 Ford Probe automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1992 Ford Probe
- 1992 Ford Probe GL 2.2 L4 GAS, CID:133, Fuel Injection, Aspiration:133, Engine VIN:, Desg:C
- 1992 Ford Probe GT 2.2 L4 GAS, CID:133, Fuel Injection, Aspiration:133, Engine VIN:, Desg:L
- 1992 Ford Probe LX 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:U
MAINTENANCE LAMP RESET PROCEDURES FOR 1992 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1992 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Check Fuel Cap Lamp ->
Vehicle: 1992 Ford Probe GT 2.2 L4 GAS
The Check Fuel Cap Lamp will illuminate momentarily when the ignition switch is placed in the On position as a bulb check. If the lamp remains...
CLICK HERE TO GET FULL ACCESS TO 1992 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1992 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1992 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Service Interval Reminder -> Probe -> Electronic Instrument Cluster -> Vehicle Maintenance Monitor
Vehicle: 1992 Ford Probe LX 3.0 V6 GAS
Electronic Instrument Cluster
At 7500 mile intervals, a Service Check message will be displayed under the System Scanner nomenclature on the instrument cluster for 3 minutes after engine starts, Fig. . After performing the required interval service, reset the service interval by depressing and holding the Service reset button, located on the speed alarm keyboard, until three tones have sounded, Fig. .
Vehicle Maintenance Monitor
At 7500 mile intervals ...
CLICK HERE TO GET FULL ACCESS TO 1992 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1992 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1992 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Check Engine Lamp/Malfunction Indicator Lamp (MIL)/Service Engine Soon Lamp -> 1990-94 Models w/EEC-IV
Vehicle: 1992 Ford Probe LX 3.0 V6 GAS
This lamp should light when the ignition is turned On. After the engine is started, the lamp should go off, unless a fault condition is detected by the EEC-IV system. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when the stored codes are cleared from the EEC-IV system memory. After diagnosis and repair, the EEC-IV memory may be cleared of stored codes as follows:
- With ignition turned Off, connect a jumper wire between Self Test and Self Test Input (STI) connectors, Fig. . On Crown Victoria, Grand Marquis and Town Car models, the...
CLICK HERE TO GET FULL ACCESS TO 1992 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1992 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1992 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Air Bag Warning Lamp ->
Vehicle: 1992 Ford Probe GT 2.2 L4 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned On as a bulb check. If the Air B...
CLICK HERE TO GET FULL ACCESS TO 1992 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1992 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1992 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Low Coolant Lamp ->
Vehicle: 1992 Ford Probe GL 2.2 L4 GAS
The low coolant warning lamp should light whenever the coolant level in the coolant recovery bottle is 1/4 to 3/4 inch or more below the cold full mark. Raise coolant level in recovery bottle to the cold full mark to turn lamp off.
On models equipped with GEM module and low coolant level warning system, t...
CLICK HERE TO GET FULL ACCESS TO 1992 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1992 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1992 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Anti-Lock Brake Warning Lamp ->
Vehicle: 1992 Ford Probe GL 2.2 L4 GAS
This lamp should light when the ignition is turned On. It may light for as long as 30 seconds as a bulb and system inspect. If the lamp remains lit or lights while operating the vehicle, a fault condition in the anti-lock brake system is indicated. When the lamp is lit, turn ignition Off, then start...
CLICK HERE TO GET FULL ACCESS TO 1992 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1992 Ford Probe vehicle.
|
| Access the Complete guide! |
